[smartmontools-support] your opinion about a seagate harddrive

[Gerard Berto]

Hello,

I have bought a new hard drive and I would like to have your opinion 
about my new hard drive. Here is the smart report:

$ sudo smartctl -a /dev/sdb
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.15.0-47-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Device Model:     ST1000DM010-2EP102
Serial Number:    ZN1179YR
LU WWN Device Id: 5 000c50 0b3e0053a
Firmware Version: CC43
User Capacity:    1 000 204 886 016 bytes [1,00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    7200 rpm
Form Factor:      3.5 inches
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Wed Apr 17 11:04:51 2019 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82)    Offline data collection activity
                     was completed without error.
                     Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)    The previous self-test 
routine completed
                     without error or no self-test has ever
                     been run.
Total time to complete Offline
data collection:         (    0) seconds.
Offline data collection
capabilities:              (0x7b) SMART execute Offline immediate.
                     Auto Offline data collection on/off support.
                     Suspend Offline collection upon new
                     command.
                     Offline surface scan supported.
                     Self-test supported.
                     Conveyance Self-test supported.
                     Selective Self-test supported.
SMART capabilities:            (0x0003)    Saves SMART data before entering
                     power-saving mode.
                     Supports SMART auto save timer.
Error logging capability:        (0x01)    Error logging supported.
                     General Purpose Logging supported.
Short self-test routine
recommended polling time:      (   1) minutes.
Extended self-test routine
recommended polling time:      ( 102) minutes.
Conveyance self-test routine
recommended polling time:      (   2) minutes.
SCT capabilities:            (0x1085)    SCT Status supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE UPDATED  
WHEN_FAILED RAW_VALUE
   1 Raw_Read_Error_Rate     0x000f   083   066   006    Pre-fail 
Always       -       204319511
   3 Spin_Up_Time            0x0003   097   097   000    Pre-fail 
Always       -       0
   4 Start_Stop_Count        0x0032   100   100   020    Old_age 
Always       -       15
   5 Reallocated_Sector_Ct   0x0033   100   100   010    Pre-fail 
Always       -       0
   7 Seek_Error_Rate         0x000f   100   253   045    Pre-fail 
Always       -       552644
   9 Power_On_Hours          0x0032   100   100   000    Old_age 
Always       -       33
  10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail 
Always       -       0
  12 Power_Cycle_Count       0x0032   100   100   020    Old_age 
Always       -       15
183 Runtime_Bad_Block       0x0032   100   100   000    Old_age 
Always       -       0
184 End-to-End_Error        0x0032   100   100   099    Old_age 
Always       -       0
187 Reported_Uncorrect      0x0032   100   100   000    Old_age 
Always       -       0
188 Command_Timeout         0x0032   100   100   000    Old_age 
Always       -       0
189 High_Fly_Writes         0x003a   100   100   000    Old_age 
Always       -       0
190 Airflow_Temperature_Cel 0x0022   074   071   040    Old_age 
Always       -       26 (Min/Max 18/26)
193 Load_Cycle_Count        0x0032   100   100   000    Old_age 
Always       -       15
194 Temperature_Celsius     0x0022   026   018   000    Old_age 
Always       -       26 (0 18 0 0 0)
195 Hardware_ECC_Recovered  0x001a   004   001   000    Old_age 
Always       -       204319511
197 Current_Pending_Sector  0x0012   100   100   000    Old_age 
Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age 
Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age 
Always       -       0
240 Head_Flying_Hours       0x0000   100   253   000    Old_age 
Offline      -       33 (24 227 0)
241 Total_LBAs_Written      0x0000   100   253   000    Old_age 
Offline      -       310079264
242 Total_LBAs_Read         0x0000   100   253   000    Old_age 
Offline      -       175067181

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
  SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
     1        0        0  Not_testing
     2        0        0  Not_testing
     3        0        0  Not_testing
     4        0        0  Not_testing
     5        0        0  Not_testing
Selective self-test flags (0x0):
   After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.



I notice that Raw_Read_Error_Rate and Seek_Error_Rate have already high 
RAW values. ||||Does this drive have a problem? Do you think I may 
return it?

I read some articles saying that seagate RAW values are often high. Is 
it right?

Thanks in advance

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://listi.jpberlin.de/pipermail/smartmontools-support/attachments/20190417/29410a2a/attachment.html>