[Smartmontools-database] Toshiba THNSNJ256GCSY
Alexander Burke
alex at alexburke.ca
Sun Mar 26 00:47:20 CET 2023
smartctl 7.3 2022-02-28 r5338 [FreeBSD 13.1-RELEASE-p6 amd64] (local build)
Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: TOSHIBA THNSNJ256GCSY
Serial Number: NNXXNNNNXNXX
LU WWN Device Id: H HHHHHH HHHHHHHHH
Firmware Version: JYPA0101
User Capacity: 256,060,514,304 bytes [256 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
TRIM Command: Available, deterministic, zeroed
Device is: Not in smartctl database 7.3/5319
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sun Mar 26 00:42:17 2023 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 254 (maximum performance)
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 10) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate -O-R-- 100 100 000 - 0
2 Throughput_Performance P-S--- 100 100 050 - 0
3 Spin_Up_Time POS--- 100 100 050 - 0
5 Reallocated_Sector_Ct PO--C- 100 100 050 - 0
7 Unknown_SSD_Attribute PO-R-- 100 100 050 - 0
8 Unknown_SSD_Attribute P-S--- 100 100 050 - 0
9 Power_On_Hours -O--C- 100 100 000 - 7627
10 Unknown_SSD_Attribute PO--C- 100 100 050 - 0
12 Power_Cycle_Count -O--C- 100 100 000 - 1056
167 Unknown_Attribute -O---K 100 100 000 - 0
168 Unknown_Attribute -O--C- 100 100 000 - 16
169 Unknown_Attribute PO--C- 100 100 010 - 100
170 Unknown_Attribute PO--C- 100 100 010 - 0
173 Unknown_Attribute -O--C- 197 197 000 - 0
175 Program_Fail_Count_Chip PO--C- 100 100 010 - 0
192 Power-Off_Retract_Count -O--C- 100 100 000 - 70
194 Temperature_Celsius -O---K 058 042 000 - 42 (Min/Max 1/58)
197 Current_Pending_Sector -O--C- 100 100 000 - 0
240 Unknown_SSD_Attribute PO--C- 100 100 050 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 51 Comprehensive SMART error log
0x03 GPL R/O 64 Ext. Comprehensive SMART error log
0x04 GPL,SL R/O 8 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (64 sectors)
Device Error Count: 8
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 8 [7] occurred at disk power-on lifetime: 7293 hours (303 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 80 00 00 01 36 49 e0 e0 00 Error: ICRC, ABRT 128 sectors at LBA = 0x013649e0 = 20335072
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
35 00 00 00 80 00 00 01 36 49 e0 e0 00 00:00:13.470 WRITE DMA EXT
35 00 00 00 80 00 00 01 36 49 60 e0 00 00:00:13.469 WRITE DMA EXT
35 00 00 00 80 00 00 01 36 48 e0 e0 00 00:00:13.469 WRITE DMA EXT
35 00 00 00 80 00 00 01 36 48 60 e0 00 00:00:13.468 WRITE DMA EXT
35 00 00 00 80 00 00 01 36 47 e0 e0 00 00:00:13.468 WRITE DMA EXT
Error 7 [6] occurred at disk power-on lifetime: 7151 hours (297 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 00 00 00 00 90 f5 00 40 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ff ff ff ff ff ff ff ff ff ff ff ff ff 00:00:22.676 [VENDOR SPECIFIC]
60 00 80 00 70 00 00 00 18 16 78 40 00 00:00:22.676 READ FPDMA QUEUED
60 00 78 00 68 00 00 00 d7 da b0 40 00 00:00:22.676 READ FPDMA QUEUED
60 00 48 00 60 00 00 00 d7 da 40 40 00 00:00:22.676 READ FPDMA QUEUED
60 00 50 00 58 00 00 00 d7 97 58 40 00 00:00:22.676 READ FPDMA QUEUED
Error 6 [5] occurred at disk power-on lifetime: 7095 hours (295 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 60 00 00 00 61 c4 18 40 00 Error: ICRC, ABRT at LBA = 0x0061c418 = 6407192
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 80 00 60 00 00 00 61 c4 18 40 00 00:00:15.716 READ FPDMA QUEUED
60 00 80 00 58 00 00 00 61 c3 98 40 00 00:00:15.716 READ FPDMA QUEUED
60 00 80 00 50 00 00 00 61 c3 18 40 00 00:00:15.716 READ FPDMA QUEUED
60 00 80 00 48 00 00 00 61 c2 98 40 00 00:00:15.716 READ FPDMA QUEUED
60 00 40 00 40 00 00 00 c8 0e a8 40 00 00:00:15.715 READ FPDMA QUEUED
Error 5 [4] occurred at disk power-on lifetime: 4820 hours (200 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 00 00 00 08 e8 23 78 40 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ff ff ff ff ff ff ff ff ff ff ff ff ff 00:06:21.289 [VENDOR SPECIFIC]
60 01 00 00 10 00 00 08 e8 25 78 40 00 00:06:21.288 READ FPDMA QUEUED
60 01 00 00 08 00 00 08 e8 24 78 40 00 00:06:21.288 READ FPDMA QUEUED
60 01 00 00 00 00 00 08 e8 23 78 40 00 00:06:21.288 READ FPDMA QUEUED
60 01 00 00 f8 00 00 08 e8 22 78 40 00 00:06:21.288 READ FPDMA QUEUED
Error 4 [3] occurred at disk power-on lifetime: 4411 hours (183 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 00 00 00 00 2f 2d 88 40 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ff ff ff ff ff ff ff ff ff ff ff ff ff 00:00:25.044 [VENDOR SPECIFIC]
60 01 00 00 30 00 00 00 2f 33 88 40 00 00:00:25.044 READ FPDMA QUEUED
60 01 00 00 28 00 00 00 2f 32 88 40 00 00:00:25.044 READ FPDMA QUEUED
60 01 00 00 20 00 00 00 2f 31 88 40 00 00:00:25.044 READ FPDMA QUEUED
60 01 00 00 18 00 00 00 2f 30 88 40 00 00:00:25.044 READ FPDMA QUEUED
Error 3 [2] occurred at disk power-on lifetime: 4411 hours (183 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 00 00 00 00 3f ee 58 40 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ff ff ff ff ff ff ff ff ff ff ff ff ff 00:00:21.944 [VENDOR SPECIFIC]
60 00 80 00 18 00 00 00 11 9e 78 40 00 00:00:21.944 READ FPDMA QUEUED
60 00 80 00 10 00 00 00 11 9d f8 40 00 00:00:21.944 READ FPDMA QUEUED
60 00 08 00 08 00 00 00 8e 48 d0 40 00 00:00:21.943 READ FPDMA QUEUED
60 00 38 00 00 00 00 00 3f ee 58 40 00 00:00:21.943 READ FPDMA QUEUED
Error 2 [1] occurred at disk power-on lifetime: 2529 hours (105 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 48 00 00 00 7a 6a c9 40 00 Error: ICRC, ABRT at LBA = 0x007a6ac9 = 8022729
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 80 00 50 00 00 00 7a 6b 49 40 00 00:06:33.110 READ FPDMA QUEUED
60 00 80 00 48 00 00 00 7a 6a c9 40 00 00:06:33.110 READ FPDMA QUEUED
60 00 60 00 40 00 00 00 7a 6a 69 40 00 00:06:33.109 READ FPDMA QUEUED
60 00 60 00 38 00 00 00 7a 6a 09 40 00 00:06:33.109 READ FPDMA QUEUED
60 00 70 00 30 00 00 00 7a 69 99 40 00 00:06:33.108 READ FPDMA QUEUED
Error 1 [0] occurred at disk power-on lifetime: 2351 hours (97 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 00 00 00 00 62 21 42 40 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ff ff ff ff ff ff ff ff ff ff ff ff ff 00:06:21.429 [VENDOR SPECIFIC]
60 00 44 00 a8 00 00 00 62 29 d6 40 00 00:06:21.429 READ FPDMA QUEUED
60 00 44 00 a0 00 00 00 62 29 92 40 00 00:06:21.429 READ FPDMA QUEUED
60 00 48 00 98 00 00 00 62 29 4a 40 00 00:06:21.428 READ FPDMA QUEUED
60 00 48 00 90 00 00 00 62 29 02 40 00 00:06:21.428 READ FPDMA QUEUED
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 7627 -
# 2 Extended offline Completed without error 00% 7303 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 3 (0x0003)
Device State: Active (0)
Current Temperature: 42 Celsius
Power Cycle Min/Max Temperature: 23/42 Celsius
Lifetime Min/Max Temperature: 1/58 Celsius
Under/Over Temperature Limit Count: 0/42
Vendor specific:
00 00 04 00 01 01 00 05 05 00 00 00 00 00 00 00
00 01 00 00 7f 03 a3 01 02 02 00 00 00 00 00 06
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 5/40 Celsius
Min/Max Temperature Limit: 0/80 Celsius
Temperature History Size (Index): 128 (66)
Index Estimated Time Temperature Celsius
67 2023-03-25 22:35 39 ********************
... ..( 2 skipped). .. ********************
70 2023-03-25 22:38 39 ********************
71 2023-03-25 22:39 40 *********************
... ..( 6 skipped). .. *********************
78 2023-03-25 22:46 40 *********************
79 2023-03-25 22:47 41 **********************
... ..( 10 skipped). .. **********************
90 2023-03-25 22:58 41 **********************
91 2023-03-25 22:59 42 ***********************
... ..( 18 skipped). .. ***********************
110 2023-03-25 23:18 42 ***********************
111 2023-03-25 23:19 41 **********************
... ..( 6 skipped). .. **********************
118 2023-03-25 23:26 41 **********************
119 2023-03-25 23:27 40 *********************
... ..( 21 skipped). .. *********************
13 2023-03-25 23:49 40 *********************
14 2023-03-25 23:50 39 ********************
... ..( 43 skipped). .. ********************
58 2023-03-26 00:34 39 ********************
59 2023-03-26 00:35 40 *********************
... ..( 4 skipped). .. *********************
64 2023-03-26 00:40 40 *********************
65 2023-03-26 00:41 41 **********************
66 2023-03-26 00:42 42 ***********************
SCT Error Recovery Control:
Read: 600 (60.0 seconds)
Write: 600 (60.0 seconds)
Device Statistics (GP Log 0x04)
Page Offset Size Value Flags Description
0x01 ===== = = === == General Statistics (rev 2) ==
0x01 0x008 4 1056 --- Lifetime Power-On Resets
0x01 0x018 6 14034555421 --- Logical Sectors Written
0x01 0x020 6 384828139 --- Number of Write Commands
0x01 0x028 6 25736105275 --- Logical Sectors Read
0x01 0x030 6 261355757 --- Number of Read Commands
0x04 ===== = = === == General Errors Statistics (rev 1) ==
0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors
0x04 0x010 4 9 --- Resets Between Cmd Acceptance and Completion
0x05 ===== = = === == Temperature Statistics (rev 1) ==
0x05 0x008 1 42 --- Current Temperature
0x05 0x010 1 38 --- Average Short Term Temperature
0x05 0x018 1 29 --- Average Long Term Temperature
0x05 0x020 1 55 --- Highest Temperature
0x05 0x028 1 4 --- Lowest Temperature
0x05 0x030 1 45 --- Highest Average Short Term Temperature
0x05 0x038 1 14 --- Lowest Average Short Term Temperature
0x05 0x040 1 31 --- Highest Average Long Term Temperature
0x05 0x048 1 25 --- Lowest Average Long Term Temperature
0x05 0x050 4 12280 --- Time in Over-Temperature
0x05 0x058 1 40 --- Specified Maximum Operating Temperature
0x05 0x060 4 410 --- Time in Under-Temperature
0x05 0x068 1 5 --- Specified Minimum Operating Temperature
0x06 ===== = = === == Transport Statistics (rev 1) ==
0x06 0x008 4 3364 --- Number of Hardware Resets
0x06 0x018 4 16 --- Number of Interface CRC Errors
0x07 ===== = = === == Solid State Device Statistics (rev 1) ==
0x07 0x008 1 3 N-- Percentage Used Endurance Indicator
|||_ C monitored condition met
||__ D supports DSN
|___ N normalized value
Pending Defects log (GP Log 0x0c) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 4 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 4 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 4 3 Transition from drive PhyRdy to drive PhyNRdy
0x000a 4 4 Device-to-host register FISes sent due to a COMRESET
0x000b 4 0 CRC errors within host-to-device FIS
0x000d 4 0 Non-CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC
More information about the Smartmontools-database
mailing list