[Smartmontools-database] toshiba THNSNH512GBST
Coran FISHER
salyavin at gokuraku.fcac.com
Mon Jul 4 02:08:16 CEST 2022
This is an internal SSD drive. I was wondering about the possibility of
adding it to the database.
-------------- next part --------------
smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.18.4-gentoo] (local build)
Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: TOSHIBA THNSNH512GBST
Serial Number: 43BS10DVTECY
LU WWN Device Id: 5 00080d b0002d2d6
Firmware Version: HTRAN101
User Capacity: 512,110,190,592 bytes [512 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
TRIM Command: Available, deterministic, zeroed
Device is: Not in smartctl database 7.3/5319
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sun Jul 3 18:05:56 2022 MDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 254 (maximum performance)
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 27) minutes.
SCT capabilities: (0x0039) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate -O-R-- 100 100 000 - 0
2 Throughput_Performance P-S--- 100 100 050 - 0
3 Spin_Up_Time POS--- 100 100 050 - 0
5 Reallocated_Sector_Ct PO--C- 100 100 050 - 0
7 Unknown_SSD_Attribute PO-R-- 100 100 050 - 0
8 Unknown_SSD_Attribute P-S--- 100 100 050 - 0
9 Power_On_Hours -O--C- 100 100 000 - 77210
10 Unknown_SSD_Attribute PO--C- 100 100 050 - 0
12 Power_Cycle_Count -O--C- 100 100 000 - 1047
167 Unknown_Attribute -O---K 100 100 000 - 0
168 Unknown_Attribute -O--C- 100 100 000 - 2
169 Unknown_Attribute PO--C- 100 100 010 - 100
173 Unknown_Attribute -O--C- 064 064 000 - 0
175 Program_Fail_Count_Chip PO--C- 100 100 010 - 0
192 Power-Off_Retract_Count -O--C- 100 100 000 - 972
194 Temperature_Celsius PO---K 058 051 020 - 42 (Min/Max 12/49)
197 Current_Pending_Sector -O--C- 100 100 000 - 0
240 Unknown_SSD_Attribute PO--C- 100 100 050 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 51 Comprehensive SMART error log
0x03 GPL R/O 64 Ext. Comprehensive SMART error log
0x04 GPL,SL R/O 8 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (64 sectors)
Device Error Count: 3
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 3 [2] occurred at disk power-on lifetime: 28604 hours (1191 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 a8 00 00 2d 4f 38 08 40 08 Error: ICRC, ABRT at LBA = 0x2d4f3808 = 760166408
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 06 c0 00 b0 00 00 2d 4f 40 08 40 08 9d+00:07:28.004 READ FPDMA QUEUED
60 08 00 00 a8 00 00 2d 4f 38 08 40 08 9d+00:07:28.001 READ FPDMA QUEUED
60 08 00 00 a0 00 00 2d 4f 30 08 40 08 9d+00:07:27.999 READ FPDMA QUEUED
60 08 00 00 98 00 00 2d 4f 28 08 40 08 9d+00:07:27.997 READ FPDMA QUEUED
60 08 00 00 90 00 00 2d 4f 20 08 40 08 9d+00:07:27.995 READ FPDMA QUEUED
Error 2 [1] occurred at disk power-on lifetime: 22811 hours (950 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 c8 00 00 21 c7 a8 c0 40 08 Error: ICRC, ABRT at LBA = 0x21c7a8c0 = 566732992
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 04 00 00 c8 00 00 21 c7 a8 c0 40 08 00:54:17.035 READ FPDMA QUEUED
60 04 00 00 c0 00 00 21 c7 a4 c0 40 08 00:54:17.032 READ FPDMA QUEUED
60 04 00 00 b8 00 00 21 c7 a0 c0 40 08 00:54:17.031 READ FPDMA QUEUED
60 04 00 00 b0 00 00 21 c7 9c c0 40 08 00:54:17.029 READ FPDMA QUEUED
60 04 00 00 a8 00 00 21 c7 98 c0 40 08 00:54:17.028 READ FPDMA QUEUED
Error 1 [0] occurred at disk power-on lifetime: 11774 hours (490 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 48 00 00 10 16 f2 c0 40 08 Error: UNC at LBA = 0x1016f2c0 = 269939392
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 01 00 00 48 00 00 10 16 f2 c0 40 08 00:35:03.901 READ FPDMA QUEUED
60 00 70 00 40 00 00 2a 89 e0 c0 40 08 00:35:03.900 READ FPDMA QUEUED
60 00 98 00 38 00 00 22 f6 58 28 40 08 00:35:03.900 READ FPDMA QUEUED
60 01 c8 00 30 00 00 1b d7 e0 c0 40 08 00:35:03.900 READ FPDMA QUEUED
60 02 00 00 28 00 00 10 16 f0 c0 40 08 00:35:03.900 READ FPDMA QUEUED
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 11674 -
# 2 Extended offline Completed without error 00% 11673 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 3 (0x0003)
Device State: Active (0)
Current Temperature: 42 Celsius
Power Cycle Min/Max Temperature: 37/49 Celsius
Lifetime Min/Max Temperature: 12/49 Celsius
Specified Max Operating Temperature: 12 Celsius
Under/Over Temperature Limit Count: 0/18
Vendor specific:
00 00 04 00 05 01 00 05 05 00 00 00 00 00 00 00
00 01 00 00 7f 48 91 10 04 04 00 00 00 00 00 05
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 5/40 Celsius
Min/Max Temperature Limit: 0/80 Celsius
Temperature History Size (Index): 128 (20)
Index Estimated Time Temperature Celsius
21 2022-07-03 15:58 40 *********************
... ..( 16 skipped). .. *********************
38 2022-07-03 16:15 40 *********************
39 2022-07-03 16:16 ? -
40 2022-07-03 16:17 39 ********************
... ..( 4 skipped). .. ********************
45 2022-07-03 16:22 39 ********************
46 2022-07-03 16:23 38 *******************
... ..( 32 skipped). .. *******************
79 2022-07-03 16:56 38 *******************
80 2022-07-03 16:57 40 *********************
81 2022-07-03 16:58 43 ************************
82 2022-07-03 16:59 44 *************************
83 2022-07-03 17:00 46 ***************************
84 2022-07-03 17:01 47 ****************************
85 2022-07-03 17:02 48 *****************************
86 2022-07-03 17:03 48 *****************************
87 2022-07-03 17:04 48 *****************************
88 2022-07-03 17:05 49 ******************************
... ..( 2 skipped). .. ******************************
91 2022-07-03 17:08 49 ******************************
92 2022-07-03 17:09 47 ****************************
93 2022-07-03 17:10 45 **************************
94 2022-07-03 17:11 44 *************************
95 2022-07-03 17:12 43 ************************
96 2022-07-03 17:13 42 ***********************
97 2022-07-03 17:14 41 **********************
98 2022-07-03 17:15 40 *********************
99 2022-07-03 17:16 40 *********************
100 2022-07-03 17:17 40 *********************
101 2022-07-03 17:18 39 ********************
... ..( 3 skipped). .. ********************
105 2022-07-03 17:22 39 ********************
106 2022-07-03 17:23 38 *******************
... ..( 10 skipped). .. *******************
117 2022-07-03 17:34 38 *******************
118 2022-07-03 17:35 37 ******************
... ..( 27 skipped). .. ******************
18 2022-07-03 18:03 37 ******************
19 2022-07-03 18:04 40 *********************
20 2022-07-03 18:05 42 ***********************
SCT Error Recovery Control:
Read: 600 (60.0 seconds)
Write: 600 (60.0 seconds)
Device Statistics (GP Log 0x04)
Page Offset Size Value Flags Description
0x01 ===== = = === == General Statistics (rev 2) ==
0x01 0x008 4 1047 --- Lifetime Power-On Resets
0x01 0x018 6 137300696856 --- Logical Sectors Written
0x01 0x020 6 1630187873 --- Number of Write Commands
0x01 0x028 6 149300973922 --- Logical Sectors Read
0x01 0x030 6 792962114 --- Number of Read Commands
0x04 ===== = = === == General Errors Statistics (rev 1) ==
0x04 0x008 4 1 --- Number of Reported Uncorrectable Errors
0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion
0x05 ===== = = === == Temperature Statistics (rev 1) ==
0x05 0x008 1 42 --- Current Temperature
0x05 0x010 1 35 --- Average Short Term Temperature
0x05 0x018 1 32 --- Average Long Term Temperature
0x05 0x020 1 47 --- Highest Temperature
0x05 0x028 1 12 --- Lowest Temperature
0x05 0x030 1 41 --- Highest Average Short Term Temperature
0x05 0x038 1 17 --- Lowest Average Short Term Temperature
0x05 0x040 1 38 --- Highest Average Long Term Temperature
0x05 0x048 1 21 --- Lowest Average Long Term Temperature
0x05 0x050 4 33150 --- Time in Over-Temperature
0x05 0x058 1 40 --- Specified Maximum Operating Temperature
0x05 0x060 4 0 --- Time in Under-Temperature
0x05 0x068 1 5 --- Specified Minimum Operating Temperature
0x06 ===== = = === == Transport Statistics (rev 1) ==
0x06 0x008 4 450 --- Number of Hardware Resets
0x06 0x018 4 2 --- Number of Interface CRC Errors
0x07 ===== = = === == Solid State Device Statistics (rev 1) ==
0x07 0x008 1 136 N-- Percentage Used Endurance Indicator
|||_ C monitored condition met
||__ D supports DSN
|___ N normalized value
Pending Defects log (GP Log 0x0c) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 4 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 4 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 4 2 Transition from drive PhyRdy to drive PhyNRdy
0x000a 4 3 Device-to-host register FISes sent due to a COMRESET
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC
More information about the Smartmontools-database
mailing list