[Smartmontools-database] SAMSUNG HD161HJ
Andrey Ponomarenko
andrewponomarenko at yandex.ru
Thu Jun 14 11:57:34 CEST 2018
https://github.com/linuxhw/SMART/tree/master/HDD/Samsung/HD161/HD161HJ
=== START OF INFORMATION SECTION ===
Device Model: SAMSUNG HD161HJ
Serial Number: --
LU WWN Device Id: 5 0000f0 ...
Firmware Version: JF100-19
User Capacity: 160 040 803 840 bytes [160 GB]
Sector Size: 512 bytes logical/physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ATA/ATAPI-7, ATA8-ACS T13/1699-D revision 3b
Local Time is: Tue Jun 5 17:48:59 2018 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM level is: 254 (maximum performance), recommended: 254
APM feature is: Disabled
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 3000) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 51) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-- 100 099 051 - 0
3 Spin_Up_Time POS--- 253 253 025 - 4672
4 Start_Stop_Count -O--CK 095 095 000 - 5871
5 Reallocated_Sector_Ct PO--CK 253 253 010 - 0
7 Seek_Error_Rate POSR-- 253 253 051 - 0
8 Seek_Time_Performance P-S--K 253 253 015 - 0
9 Power_On_Hours -O--CK 100 100 000 - 10043
10 Spin_Retry_Count PO--CK 253 253 051 - 0
11 Calibration_Retry_Count -O--C- 253 253 000 - 0
12 Power_Cycle_Count -O--CK 098 098 000 - 2958
13 Read_Soft_Error_Rate -OSR-- 100 100 000 - 1578176
184 End-to-End_Error PO--CK 253 253 099 - 0
187 Reported_Uncorrect -O--CK 253 253 000 - 589824
188 Command_Timeout -O--CK 253 253 000 - 0
190 Airflow_Temperature_Cel -O---K 154 115 000 - 28 (Min/Max 1/41)
194 Temperature_Celsius -O---K 151 112 000 - 29 (Min/Max 1/42)
195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 1578176
196 Reallocated_Event_Count -O--CK 253 253 000 - 0
197 Current_Pending_Sector -O--C- 253 253 000 - 0
198 Offline_Uncorrectable ----CK 253 253 000 - 0
199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 442
200 Multi_Zone_Error_Rate -O-R-- 100 100 000 - 0
201 Soft_Read_Error_Rate -O-R-- 253 100 000 - 0
202 Data_Address_Mark_Errs -O--CK 253 253 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 2 Comprehensive SMART error log
0x03 GPL R/O 2 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x10 GPL R/O 1 SATA NCQ Queued Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
Device Error Count: 1587 (device log contains only the most recent 8 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1587 [2] log entry is empty
Error 1586 [1] log entry is empty
Error 1585 [0] log entry is empty
Error 1584 [7] occurred at disk power-on lifetime: 9853 hours (410 days + 13 hours)
When the command that caused the error occurred, the device was in a vendor specific state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
80 -- 00 57 00 e0 b2 91 00 00 00 39 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
fd 00 80 04 9f 29 00 00 e0 c6 5b 00 00 00:00:00.058 [VENDOR SPECIFIC]
fd 00 80 07 d7 39 00 00 e0 db d9 00 00 00:00:00.058 [VENDOR SPECIFIC]
bf 00 80 07 57 39 00 00 e0 db d9 00 00 00:00:00.058 [RESERVED]
bf 00 80 07 d7 39 00 00 e0 db d8 00 00 00:00:00.058 [RESERVED]
00 00 16 01 95 00 00 20 c0 00 20 06 a1 00:00:08.256 NOP [Reserved subcommand] [OBS-ACS-2]
Error 1583 [6] occurred at disk power-on lifetime: 8331 hours (347 days + 3 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
80 -- 00 ef 00 e0 cf 7c 00 00 07 34 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
77 00 14 00 47 24 00 00 e0 0d df 00 00 00:00:00.013 SET DATE & TIME EXT
77 00 08 04 d7 34 00 00 e0 dc 9c 00 00 00:00:00.013 SET DATE & TIME EXT
3f 00 00 00 86 c6 00 00 a0 cf 7d 00 00 00:00:00.013 WRITE LOG EXT
00 00 16 01 95 00 00 20 c0 00 20 05 a1 00:00:08.256 NOP [Reserved subcommand] [OBS-ACS-2]
Error 1582 [5] occurred at disk power-on lifetime: 8324 hours (346 days + 20 hours)
When the command that caused the error occurred, the device was in a vendor specific state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
80 -- 00 6f 00 e0 cf 7d 00 00 07 34 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
3f 00 00 00 fe c6 00 00 a0 cf 7c 00 00 00:00:00.013 WRITE LOG EXT
00 00 16 01 95 00 00 20 c0 00 20 04 a1 00:00:08.256 NOP [Reserved subcommand] [OBS-ACS-2]
Error 1581 [4] occurred at disk power-on lifetime: 8324 hours (346 days + 20 hours)
When the command that caused the error occurred, the device was doing SMART Offline or Self-test.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
80 -- 00 ef 00 e0 cf 7c 00 00 07 39 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
89 00 08 07 e7 29 00 00 e0 ce 41 00 00 00:00:00.013 [VENDOR SPECIFIC]
89 00 08 07 df 29 00 00 e0 ce 41 00 00 00:00:00.013 [VENDOR SPECIFIC]
ce 00 08 07 af 29 00 00 e0 ce 3c 00 00 00:00:00.013 WRITE MULTIPLE FUA EXT
ce 00 08 07 a7 29 00 00 e0 ce 3c 00 00 00:00:00.013 WRITE MULTIPLE FUA EXT
06 11 89 11 91 00 00 11 03 c9 b1 04 11 00:00:00.000 DATA SET MANAGEMENT
Error 1580 [3] occurred at disk power-on lifetime: 25408 hours (1058 days + 16 hours)
When the command that caused the error occurred, the device was in a reserved state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 00 00 00 00 00 00 00 00 00 00 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
SMART Extended Self-test Log (GP Log 0x07) not supported
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 2
SCT Version (vendor specific): 256 (0x0100)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 29 Celsius
Power Cycle Min/Max Temperature: 25/29 Celsius
Lifetime Min/Max Temperature: 2/43 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: -4/72 Celsius
Min/Max Temperature Limit: -9/77 Celsius
Temperature History Size (Index): 128 (113)
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 1 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 4 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC
0x8001 2 0 Vendor specific
More information about the Smartmontools-database
mailing list