[Smartmontools-database] TOSHIBA MK1059GSMP
Andrey Ponomarenko
andrewponomarenko at yandex.ru
Thu Jun 14 10:43:01 CEST 2018
Hi,
Please add drive: https://github.com/linuxhw/SMART/blob/master/HDD/Toshiba/MK1059/MK1059GSMP/417602858905
=== START OF INFORMATION SECTION ===
Device Model: TOSHIBA MK1059GSMP
Serial Number: --
LU WWN Device Id: 5 000039 ...
Firmware Version: GU001J
User Capacity: 1 000 204 886 016 bytes [1,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Wed Jun 6 22:54:11 2018 +09
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 128 (minimum power consumption without standby)
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 300) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 0
2 Throughput_Performance P-S--- 100 100 050 - 0
3 Spin_Up_Time POS--K 100 100 001 - 3014
4 Start_Stop_Count -O--CK 100 100 000 - 2020
5 Reallocated_Sector_Ct PO--CK 100 100 050 - 8
7 Seek_Error_Rate PO-R-- 100 100 050 - 0
8 Seek_Time_Performance P-S--- 100 100 050 - 0
9 Power_On_Hours -O--CK 092 092 000 - 3319
10 Spin_Retry_Count PO--CK 139 100 030 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 1116
191 G-Sense_Error_Rate -O--CK 100 100 000 - 6938
192 Power-Off_Retract_Count -O--CK 100 100 000 - 338
193 Load_Cycle_Count -O--CK 099 099 000 - 10430
194 Temperature_Celsius -O---K 100 100 000 - 36 (Min/Max 10/46)
196 Reallocated_Event_Count -O--CK 100 100 000 - 1
197 Current_Pending_Sector -O--CK 100 100 000 - 0
198 Offline_Uncorrectable ----CK 100 100 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
220 Disk_Shift -O---- 100 100 000 - 41
222 Loaded_Hours -O--CK 096 096 000 - 1726
223 Load_Retry_Count -O--CK 100 100 000 - 0
224 Load_Friction -O---K 100 100 000 - 0
226 Load-in_Time -OS--K 100 100 000 - 351
240 Head_Flying_Hours P----- 100 100 001 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 51 Comprehensive SMART error log
0x03 GPL R/O 64 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 SATA NCQ Queued Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (64 sectors)
Device Error Count: 20015 (device log contains only the most recent 256 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 20015 [46] occurred at disk power-on lifetime: 1991 hours (82 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 01 00 00 02 43 30 89 e2 00 Error: UNC at LBA = 0x02433089 = 37957769
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
24 00 00 00 01 00 00 02 43 30 89 e0 00 00:11:28.111 READ SECTOR(S) EXT
2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:11:28.110 READ LOG EXT
60 00 01 00 70 00 00 02 43 30 89 40 00 00:11:27.876 READ FPDMA QUEUED
60 00 01 00 68 00 00 02 43 30 88 40 00 00:11:27.874 READ FPDMA QUEUED
60 00 01 00 60 00 00 02 43 30 87 40 00 00:11:27.873 READ FPDMA QUEUED
Error 20014 [45] occurred at disk power-on lifetime: 1991 hours (82 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 41 00 72 00 00 02 43 30 89 62 00 Error: UNC at LBA = 0x02433089 = 37957769
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 01 00 70 00 00 02 43 30 89 40 00 00:11:27.876 READ FPDMA QUEUED
60 00 01 00 68 00 00 02 43 30 88 40 00 00:11:27.874 READ FPDMA QUEUED
60 00 01 00 60 00 00 02 43 30 87 40 00 00:11:27.873 READ FPDMA QUEUED
60 00 01 00 58 00 00 02 43 30 86 40 00 00:11:27.873 READ FPDMA QUEUED
60 00 01 00 50 00 00 02 43 30 85 40 00 00:11:27.873 READ FPDMA QUEUED
Error 20013 [44] occurred at disk power-on lifetime: 1987 hours (82 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 01 00 00 02 43 30 88 e2 00 Error: UNC at LBA = 0x02433088 = 37957768
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
24 00 00 00 01 00 00 02 43 30 88 e0 00 02:22:17.149 READ SECTOR(S) EXT
ff ff ff ff ff ff ff ff ff ff ff ff 0c 02:22:16.885 [VENDOR SPECIFIC]
42 00 00 00 01 00 00 02 43 30 88 e0 00 02:22:16.635 READ VERIFY SECTOR(S) EXT
42 00 00 00 01 00 00 02 43 30 87 e0 00 02:22:16.634 READ VERIFY SECTOR(S) EXT
42 00 00 00 01 00 00 02 43 30 86 e0 00 02:22:16.632 READ VERIFY SECTOR(S) EXT
Error 20012 [43] occurred at disk power-on lifetime: 1986 hours (82 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 41 00 6a 00 00 02 43 30 8c 62 00 Error: UNC at LBA = 0x0243308c = 37957772
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 f8 00 68 00 00 02 43 30 8c 40 00 02:05:18.793 READ FPDMA QUEUED
ea 00 00 00 00 00 00 00 00 00 00 a0 00 02:05:18.512 FLUSH CACHE EXT
61 00 08 00 58 00 00 1c 47 80 b5 40 00 02:05:18.511 WRITE FPDMA QUEUED
ea 00 00 00 00 00 00 00 00 00 00 a0 00 02:05:18.467 FLUSH CACHE EXT
61 00 08 00 48 00 00 1c 47 80 ad 40 00 02:05:18.467 WRITE FPDMA QUEUED
Error 20011 [42] occurred at disk power-on lifetime: 1986 hours (82 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 41 00 a2 00 00 02 43 30 8c 62 00 Error: UNC at LBA = 0x0243308c = 37957772
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 f8 00 a0 00 00 02 43 30 8c 40 00 02:05:14.038 READ FPDMA QUEUED
ef 02 90 00 03 00 00 00 00 00 00 a0 00 02:05:13.067 SET FEATURES [Disable SATA feature]
ef f8 02 01 00 00 00 01 00 00 00 a0 00 02:05:13.067 SET FEATURES [Enable write cache]
aa aa aa aa aa aa aa aa aa aa aa aa ff 02:05:13.038 [RESERVED]
60 00 f8 00 98 00 00 02 43 30 8c 40 00 02:05:09.271 READ FPDMA QUEUED
Error 20010 [41] occurred at disk power-on lifetime: 1986 hours (82 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 41 00 9a 00 00 02 43 30 8c 62 00 Error: UNC at LBA = 0x0243308c = 37957772
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 f8 00 98 00 00 02 43 30 8c 40 00 02:05:09.271 READ FPDMA QUEUED
ef 02 90 00 03 00 00 00 00 00 00 a0 00 02:05:08.300 SET FEATURES [Disable SATA feature]
ef f8 02 01 00 00 00 01 00 00 00 a0 00 02:05:08.300 SET FEATURES [Enable write cache]
aa aa aa aa aa aa aa aa aa aa aa aa ff 02:05:08.271 [RESERVED]
60 00 f8 00 90 00 00 02 43 30 8c 40 00 02:05:04.560 READ FPDMA QUEUED
Error 20009 [40] occurred at disk power-on lifetime: 1986 hours (82 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 41 00 92 00 00 02 43 30 8c 62 00 Error: UNC at LBA = 0x0243308c = 37957772
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 f8 00 90 00 00 02 43 30 8c 40 00 02:05:04.560 READ FPDMA QUEUED
ef 02 90 00 03 00 00 00 00 00 00 a0 00 02:05:03.723 SET FEATURES [Disable SATA feature]
ef 11 02 00 00 00 00 07 00 00 00 a0 00 02:05:03.655 SET FEATURES [Enable write cache]
60 00 08 00 88 00 00 02 43 31 84 40 00 02:05:03.590 READ FPDMA QUEUED
ef f8 90 01 03 00 00 01 00 00 00 a0 00 02:05:03.590 SET FEATURES [Disable SATA feature]
Error 20008 [39] occurred at disk power-on lifetime: 1986 hours (82 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 41 00 82 00 00 02 43 30 8c 62 00 Error: UNC at LBA = 0x0243308c = 37957772
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 f8 00 80 00 00 02 43 30 8c 40 00 02:04:59.813 READ FPDMA QUEUED
ef 01 02 01 00 00 00 01 00 00 00 a0 00 02:04:59.813 SET FEATURES [Enable write cache]
aa aa aa aa aa aa aa aa aa aa aa aa ff 02:04:59.782 [RESERVED]
60 00 01 00 78 00 00 02 43 30 8b 40 00 02:04:56.015 READ FPDMA QUEUED
ef 02 90 00 03 00 00 00 00 00 00 a0 00 02:04:55.046 SET FEATURES [Disable SATA feature]
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 3078 -
# 2 Short offline Completed without error 00% 2709 -
# 3 Short offline Completed without error 00% 2425 -
# 4 Short offline Completed without error 00% 2207 -
# 5 Short offline Completed without error 00% 2145 -
# 6 Short offline Completed: read failure 00% 1991 37957769
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 2
SCT Version (vendor specific): 1 (0x0001)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 36 Celsius
Power Cycle Min/Max Temperature: 29/38 Celsius
Lifetime Min/Max Temperature: 10/46 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 5/55 Celsius
Min/Max Temperature Limit: 5/55 Celsius
Temperature History Size (Index): 478 (106)
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 4 0 Command failed due to ICRC error
0x0002 4 0 R_ERR response for data FIS
0x0003 4 0 R_ERR response for device-to-host data FIS
0x0004 4 0 R_ERR response for host-to-device data FIS
0x0005 4 0 R_ERR response for non-data FIS
0x0006 4 0 R_ERR response for device-to-host non-data FIS
0x0007 4 0 R_ERR response for host-to-device non-data FIS
0x0008 4 0 Device-to-host non-data FIS retries
0x0009 4 3867 Transition from drive PhyRdy to drive PhyNRdy
0x000a 4 11 Device-to-host register FISes sent due to a COMRESET
0x000b 4 0 CRC errors within host-to-device FIS
0x000d 4 0 Non-CRC errors within host-to-device FIS
0x000f 4 0 R_ERR response for host-to-device data FIS, CRC
0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC
More information about the Smartmontools-database
mailing list