[smartmontools-support] Somebody can explain this, in common language?
Carlos E. R.
robin.listas at telefonica.net
Mon Jun 16 19:20:36 CEST 2025
Is this disk actually defunct? I bought it this April. It is part of an 8 disk software raid 6 (linux).
Somebody can explain in common language what is going on?
I have the array umounted.
It is inside a Yottamaster Model FS5 according to the label. But according to the manual, it is “Y-Focus Series 5-Bay” FS5U3
Isengard:~/bin # smartctl --test=short /dev/sdb
smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.4.0-150600.23.47-default] (SUSE RPM)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION ===
Sending command: "Execute SMART Short self-test routine immediately in off-line mode".
Drive command "Execute SMART Short self-test routine immediately in off-line mode" successful.
Testing has begun.
Please wait 1 minutes for test to complete.
Test will complete after Mon Jun 16 18:58:51 2025 CEST
Use smartctl -X to abort test.
Isengard:~/bin # smartctl --health -d sat /dev/sdb
smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.4.0-150600.23.47-default] (SUSE RPM)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF READ SMART DATA SECTION ===
SMART Status not supported: Incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
Warning: This result is based on an Attribute check.
Failed Attributes:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 044 043 044 Pre-fail Always FAILING_NOW 7116644
Isengard:~/bin #
But it has been saying that for almost three days.
The short test doesn't actually complete.
Isengard:~/bin # smartctl -a /dev/sdb [156/1781]
smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.4.0-150600.23.47-default] (SUSE RPM)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: ST10000NT001-3LY101
Serial Number: WP022JMK
LU WWN Device Id: 5 000c50 0faa885cf
Firmware Version: EN01
User Capacity: 10,000,831,348,736 bytes [10.0 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: Not in smartctl database 7.3/5528
ATA Version is: ACS-4 (minor revision not indicated)
SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Mon Jun 16 19:06:22 2025 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART Status not supported: Incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
Warning: This result is based on an Attribute check.
See vendor-specific Attribute list for failed Attributes.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 73) The previous self-test completed having
a test element that failed and the test
element that failed is not known.
Total time to complete Offline
data collection: ( 567) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 884) minutes. [103/1781]
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x50bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 044 043 044 Pre-fail Always FAILING_NOW 7116662
3 Spin_Up_Time 0x0003 088 087 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 37
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 077 060 045 Pre-fail Always - 54626488
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 1645
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 11
18 Unknown_Attribute 0x000b 100 100 050 Pre-fail Always - 0
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 206
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 051 042 000 Old_age Always - 49 (Min/Max 24/57)
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 7
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 149
194 Temperature_Celsius 0x0022 049 058 000 Old_age Always - 49 (0 22 0 0 0)
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 4
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 4
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 100 000 Old_age Offline - 1520 (203 135 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 48860575345
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 28847272398
SMART Error Log Version: 1
ATA Error Count: 226 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 226 occurred at disk power-on lifetime: 1580 hours (65 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH [50/1781]
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff 4f 00 46d+03:17:37.431 READ DMA EXT
25 00 08 ff ff ff 4f 00 46d+03:17:32.707 READ DMA EXT
25 00 08 ff ff ff 4f 00 46d+03:17:28.192 READ DMA EXT
25 00 08 ff ff ff 4f 00 46d+03:17:23.818 READ DMA EXT
25 00 08 ff ff ff 4f 00 46d+03:17:19.411 READ DMA EXT
Error 225 occurred at disk power-on lifetime: 1580 hours (65 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff 4f 00 46d+03:17:32.707 READ DMA EXT
25 00 08 ff ff ff 4f 00 46d+03:17:28.192 READ DMA EXT
25 00 08 ff ff ff 4f 00 46d+03:17:23.818 READ DMA EXT
25 00 08 ff ff ff 4f 00 46d+03:17:19.411 READ DMA EXT
25 00 08 ff ff ff 4f 00 46d+03:17:15.095 READ DMA EXT
Error 224 occurred at disk power-on lifetime: 1580 hours (65 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff 4f 00 46d+03:17:28.192 READ DMA EXT
25 00 08 ff ff ff 4f 00 46d+03:17:23.818 READ DMA EXT
25 00 08 ff ff ff 4f 00 46d+03:17:19.411 READ DMA EXT
25 00 08 ff ff ff 4f 00 46d+03:17:15.095 READ DMA EXT
25 00 08 ff ff ff 4f 00 46d+03:17:12.396 READ DMA EXT
Error 223 occurred at disk power-on lifetime: 1580 hours (65 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff 4f 00 46d+03:17:23.818 READ DMA EXT
25 00 08 ff ff ff 4f 00 46d+03:17:19.411 READ DMA EXT
25 00 08 ff ff ff 4f 00 46d+03:17:15.095 READ DMA EXT
25 00 08 ff ff ff 4f 00 46d+03:17:12.396 READ DMA EXT
25 00 08 ff ff ff 4f 00 46d+03:17:09.772 READ DMA EXT
Error 222 occurred at disk power-on lifetime: 1580 hours (65 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff 4f 00 46d+03:17:19.411 READ DMA EXT
25 00 08 ff ff ff 4f 00 46d+03:17:15.095 READ DMA EXT
25 00 08 ff ff ff 4f 00 46d+03:17:12.396 READ DMA EXT
25 00 08 ff ff ff 4f 00 46d+03:17:09.772 READ DMA EXT
25 00 08 ff ff ff 4f 00 46d+03:17:05.606 READ DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed: unknown failure 90% 1645 0
# 2 Short offline Completed: unknown failure 90% 1626 0
# 3 Short offline Completed: unknown failure 90% 1592 0
# 4 Extended offline Completed without error 00% 13 -
# 5 Short offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
The above only provides legacy SMART information - try 'smartctl -x' for more
Isengard:~/bin #
--
Cheers / Saludos,
Carlos E. R.
(from 15.6 x86_64 at Telcontar)
More information about the Smartmontools-support
mailing list