[smartmontools-support] SAMSUNG HD103SJ failures - Spin_Up_Time + IDNF
Ohad Schneider
ohad188 at outlook.com
Sun Jul 18 12:24:18 CEST 2021
Hi,
I have a couple of Samsung HD103SJ hard drives with a few smartmontools failures (using the GSmartControl wrapper on Windows).
The important details follow, and please find below the full output for both hard drives.
------------
Failure 1
------------
Spin_Up_Time PO---K 071 001 025 Past 8895
This only happens in one of the hard drives, and I suspect it might be a real issue.
However, I wonder how seriously I should treat it since it only happened in the "Past"?
------------
Failure 2
------------
10 -- 51 00 20 00 00 74 70 6d af e0 00 Error: IDNF at LBA = 0x74706daf = 1953525167
10 -- 51 00 20 00 00 74 70 6d b0 e0 00 Error: IDNF at LBA = 0x74706db0 = 1953525168
These I get in both drives, and I suspect some OS / driver is at fault (but I could be wrong of course, far from an expert in this area).
The reason for my suspicion is that these are the absolute last sectors on the disk, so it seems unlikely to be coincidence for only the very last 2 sectors to fail.
Executing "wmic diskpart" on seemingly supported this theory, as it stated the drive only has 1953520065 total sectors (less than the reported 1953525167 / 1953525168).
However, executing "smartctl -I" and dividing the amount of "user capacity" by "bytes per sector" I get the exact number of the IDNF: 1000204886016 / 512 = 1953525168
I read that such failures in the last sectors could be attriputed to Host Protected Area (HPA) so I live booted Ubuntu and executed hdparm -N which suggested that wasn't the case:
1953525168 / 1953525168, HPA is disabled
Again, this is the exact IDNF number so I'm left confused - any idea what's going on?
--------
TESTS
--------
Both tests pass the short & extended self-tests.
The strange thing is that after I executed the tests, the Lifetime(hours) value of the newly executed tests was LOWER than the value for past tests (as if the past tests ran AFTER the test I just executed).
This happened for both drives, here's an example from one of them:
# 1 Extended offline Completed without error 00% 20387 -
# 2 Short offline Completed without error 00% 20385 -
# 3 Short offline Completed without error 00% 20190 -
# 4 Short offline Completed without error 00% 57431 -
# 5 Extended offline Completed without error 00% 48469 -
Thank you,
Ohad
P.S. is this the "old" mailing list? If so, what is the new one?
Have you considered moving to a more modern Q&A platform like StackExchange (even use an existing one like ServerFault)?
------------------
HDD 1 output
------------------
smartctl 6.6 2017-11-05 r4594 [x86_64-w64-mingw32-w10-b19042] (sf-6.6-1)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint F3
Device Model: SAMSUNG HD103SJ
Serial Number: S246JDWSB67782
LU WWN Device Id: 5 0024e9 0028b66c6
Firmware Version: 1AJ100E5
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Sat Jul 17 22:23:53 2021 JDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Disabled
APM level is: 254 (maximum performance)
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, frozen [SEC2]
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 9420) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 157) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 100 100 051 - 2
2 Throughput_Performance -OS--K 056 056 000 - 8584
3 Spin_Up_Time PO---K 071 001 025 Past 8895
4 Start_Stop_Count -O--CK 091 091 000 - 9217
5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0
7 Seek_Error_Rate -OSR-K 252 252 051 - 0
8 Seek_Time_Performance --S--K 252 252 015 - 0
9 Power_On_Hours -O--CK 100 100 000 - 85921
10 Spin_Retry_Count -O--CK 252 252 051 - 0
11 Calibration_Retry_Count -O--CK 252 252 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 462
191 G-Sense_Error_Rate -O---K 100 100 000 - 1
192 Power-Off_Retract_Count -O---K 252 252 000 - 0
194 Temperature_Celsius -O---- 064 049 000 - 35 (Min/Max 13/51)
195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0
196 Reallocated_Event_Count -O--CK 252 252 000 - 0
197 Current_Pending_Sector -O--CK 252 252 000 - 0
198 Offline_Uncorrectable ----CK 252 252 000 - 0
199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0
200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 10
223 Load_Retry_Count -O--CK 252 252 000 - 0
225 Load_Cycle_Count -O--CK 100 100 000 - 9280
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 2 Comprehensive SMART error log
0x03 GPL R/O 2 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 2 Extended self-test log
0x08 GPL R/O 2 Power Conditions log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xbb GPL VS 4 Device vendor specific log
0xbc GPL VS 2 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
Device Error Count: 3
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 3 [2] occurred at disk power-on lifetime: 48476 hours (2019 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
10 -- 51 00 20 00 00 74 70 6d af e0 00 Error: IDNF at LBA = 0x74706daf = 1953525167
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
34 00 00 00 20 00 00 74 70 6d af e0 00 00:01:51.635 WRITE SECTORS(S) EXT
24 00 00 00 20 00 00 74 70 6d 8f e0 00 00:01:51.635 READ SECTOR(S) EXT
34 00 00 00 20 00 00 74 70 6d 8f e0 00 00:01:51.635 WRITE SECTORS(S) EXT
24 00 00 00 20 00 00 74 70 6d 6f e0 00 00:01:51.635 READ SECTOR(S) EXT
34 00 00 00 20 00 00 74 70 6d 6f e0 00 00:01:51.635 WRITE SECTORS(S) EXT
Error 2 [1] occurred at disk power-on lifetime: 9346 hours (389 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
10 -- 51 00 20 00 00 74 70 6d af e0 00 Error: IDNF at LBA = 0x74706daf = 1953525167
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
34 00 00 00 20 00 00 74 70 6d af e0 00 00:00:02.920 WRITE SECTORS(S) EXT
24 00 00 00 20 00 00 74 70 6d 8f e0 00 00:00:02.920 READ SECTOR(S) EXT
34 00 00 00 20 00 00 74 70 6d 8f e0 00 00:00:02.920 WRITE SECTORS(S) EXT
24 00 00 00 20 00 00 74 70 6d 6f e0 00 00:00:02.920 READ SECTOR(S) EXT
34 00 00 00 20 00 00 74 70 6d 6f e0 00 00:00:02.920 WRITE SECTORS(S) EXT
Error 1 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
10 -- 51 00 20 00 00 74 70 6d b0 e0 00 Error: IDNF at LBA = 0x74706db0 = 1953525168
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
34 00 00 00 20 00 00 74 70 6d b0 e0 00 00:00:09.503 WRITE SECTORS(S) EXT
24 00 00 00 20 00 00 74 70 6d 90 e0 00 00:00:09.503 READ SECTOR(S) EXT
34 00 00 00 20 00 00 74 70 6d 90 e0 00 00:00:09.503 WRITE SECTORS(S) EXT
24 00 00 00 20 00 00 74 70 6d 70 e0 00 00:00:09.503 READ SECTOR(S) EXT
34 00 00 00 20 00 00 74 70 6d 70 e0 00 00:00:09.503 WRITE SECTORS(S) EXT
SMART Extended Self-test Log Version: 1 (2 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 20385 -
# 2 Short offline Completed without error 00% 20190 -
# 3 Short offline Completed without error 00% 57431 -
# 4 Extended offline Completed without error 00% 48469 -
# 5 Short offline Completed without error 00% 48467 -
# 6 Extended offline Aborted by host 90% 48467 -
# 7 Extended offline Completed without error 00% 48425 -
# 8 Short offline Completed without error 00% 48422 -
# 9 Short offline Completed without error 00% 26077 -
#10 Short offline Completed without error 00% 26030 -
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Completed [00% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 2
SCT Version (vendor specific): 256 (0x0100)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 34 Celsius
Power Cycle Min/Max Temperature: 25/42 Celsius
Lifetime Min/Max Temperature: 13/51 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 5 minutes
Temperature Logging Interval: 5 minutes
Min/Max recommended Temperature: -5/80 Celsius
Min/Max Temperature Limit: -10/85 Celsius
Temperature History Size (Index): 128 (7)
Index Estimated Time Temperature Celsius
8 2021-07-17 11:45 37 ******************
... ..( 4 skipped). .. ******************
13 2021-07-17 12:10 37 ******************
14 2021-07-17 12:15 36 *****************
15 2021-07-17 12:20 36 *****************
16 2021-07-17 12:25 36 *****************
17 2021-07-17 12:30 35 ****************
... ..( 3 skipped). .. ****************
21 2021-07-17 12:50 35 ****************
22 2021-07-17 12:55 34 ***************
... ..( 17 skipped). .. ***************
40 2021-07-17 14:25 34 ***************
41 2021-07-17 14:30 33 **************
... ..( 65 skipped). .. **************
107 2021-07-17 20:00 33 **************
108 2021-07-17 20:05 34 ***************
... ..( 2 skipped). .. ***************
111 2021-07-17 20:20 34 ***************
112 2021-07-17 20:25 33 **************
... ..( 18 skipped). .. **************
3 2021-07-17 22:00 33 **************
4 2021-07-17 22:05 34 ***************
5 2021-07-17 22:10 33 **************
6 2021-07-17 22:15 34 ***************
7 2021-07-17 22:20 34 ***************
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 4 0 Command failed due to ICRC error
0x0002 4 0 R_ERR response for data FIS
0x0003 4 0 R_ERR response for device-to-host data FIS
0x0004 4 0 R_ERR response for host-to-device data FIS
0x0005 4 0 R_ERR response for non-data FIS
0x0006 4 0 R_ERR response for device-to-host non-data FIS
0x0007 4 0 R_ERR response for host-to-device non-data FIS
0x0008 4 0 Device-to-host non-data FIS retries
0x0009 4 1059 Transition from drive PhyRdy to drive PhyNRdy
0x000a 4 1059 Device-to-host register FISes sent due to a COMRESET
0x000b 4 0 CRC errors within host-to-device FIS
0x000d 4 0 Non-CRC errors within host-to-device FIS
0x000f 4 0 R_ERR response for host-to-device data FIS, CRC
0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC
0x8e00 4 0 Vendor specific
0x8e01 4 0 Vendor specific
0x8e02 4 0 Vendor specific
0x8e03 4 0 Vendor specific
0x8e04 4 0 Vendor specific
0x8e05 4 0 Vendor specific
0x8e06 4 0 Vendor specific
0x8e07 4 0 Vendor specific
0x8e08 4 0 Vendor specific
0x8e09 4 0 Vendor specific
0x8e0a 4 0 Vendor specific
0x8e0b 4 0 Vendor specific
0x8e0c 4 0 Vendor specific
0x8e0d 4 0 Vendor specific
0x8e0e 4 0 Vendor specific
0x8e0f 4 0 Vendor specific
0x8e10 4 0 Vendor specific
0x8e11 4 0 Vendor specific
------------------
HDD 2 output
------------------
smartctl 6.6 2017-11-05 r4594 [x86_64-w64-mingw32-w10-b19042] (sf-6.6-1)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint F3
Device Model: SAMSUNG HD103SJ
Serial Number: S246J9AB804211
LU WWN Device Id: 5 0024e9 205d87535
Firmware Version: 1AJ100E5
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Sat Jul 17 22:26:26 2021 JDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Disabled
APM level is: 254 (maximum performance)
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, frozen [SEC2]
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 9300) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 155) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 100 100 051 - 205
2 Throughput_Performance -OS--K 252 252 000 - 0
3 Spin_Up_Time PO---K 071 069 025 - 8972
4 Start_Stop_Count -O--CK 092 092 000 - 8678
5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0
7 Seek_Error_Rate -OSR-K 252 252 051 - 0
8 Seek_Time_Performance --S--K 252 252 015 - 0
9 Power_On_Hours -O--CK 100 100 000 - 77746
10 Spin_Retry_Count -O--CK 252 252 051 - 0
11 Calibration_Retry_Count -O--CK 252 252 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 412
191 G-Sense_Error_Rate -O---K 252 252 000 - 0
192 Power-Off_Retract_Count -O---K 252 252 000 - 0
194 Temperature_Celsius -O---- 064 051 000 - 33 (Min/Max 13/49)
195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0
196 Reallocated_Event_Count -O--CK 252 252 000 - 0
197 Current_Pending_Sector -O--CK 252 252 000 - 0
198 Offline_Uncorrectable ----CK 252 252 000 - 0
199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0
200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 46
223 Load_Retry_Count -O--CK 252 252 000 - 0
225 Load_Cycle_Count -O--CK 100 100 000 - 8737
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 2 Comprehensive SMART error log
0x03 GPL R/O 2 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 2 Extended self-test log
0x08 GPL R/O 2 Power Conditions log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xbb GPL VS 4 Device vendor specific log
0xbc GPL VS 2 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
Device Error Count: 2
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 2 [1] occurred at disk power-on lifetime: 40255 hours (1677 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
10 -- 51 00 20 00 00 74 70 6d af e0 00 Error: IDNF at LBA = 0x74706daf = 1953525167
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
34 00 00 00 20 00 00 74 70 6d af e0 00 00:02:19.681 WRITE SECTORS(S) EXT
24 00 00 00 20 00 00 74 70 6d 8f e0 00 00:02:19.681 READ SECTOR(S) EXT
34 00 00 00 20 00 00 74 70 6d 8f e0 00 00:02:19.681 WRITE SECTORS(S) EXT
24 00 00 00 20 00 00 74 70 6d 6f e0 00 00:02:19.681 READ SECTOR(S) EXT
34 00 00 00 20 00 00 74 70 6d 6f e0 00 00:02:19.681 WRITE SECTORS(S) EXT
Error 1 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
10 -- 51 00 20 00 00 74 70 6d af e0 00 Error: IDNF at LBA = 0x74706daf = 1953525167
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
34 00 00 00 20 00 00 74 70 6d af e0 00 00:00:13.456 WRITE SECTORS(S) EXT
24 00 00 00 20 00 00 74 70 6d 8f e0 00 00:00:13.456 READ SECTOR(S) EXT
34 00 00 00 20 00 00 74 70 6d 8f e0 00 00:00:13.456 WRITE SECTORS(S) EXT
24 00 00 00 20 00 00 74 70 6d 6f e0 00 00:00:13.456 READ SECTOR(S) EXT
34 00 00 00 20 00 00 74 70 6d 6f e0 00 00:00:13.456 WRITE SECTORS(S) EXT
SMART Extended Self-test Log Version: 1 (2 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 12015 -
# 2 Short offline Completed without error 00% 12015 -
# 3 Short offline Completed without error 00% 49201 -
# 4 Short offline Completed without error 00% 16244 -
# 5 Short offline Completed without error 00% 16208 -
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Completed [00% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 2
SCT Version (vendor specific): 256 (0x0100)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 33 Celsius
Power Cycle Min/Max Temperature: 24/38 Celsius
Lifetime Min/Max Temperature: 15/49 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 5 minutes
Temperature Logging Interval: 5 minutes
Min/Max recommended Temperature: -5/80 Celsius
Min/Max Temperature Limit: -10/85 Celsius
Temperature History Size (Index): 128 (115)
Index Estimated Time Temperature Celsius
116 2021-07-17 11:50 35 ****************
... ..( 17 skipped). .. ****************
6 2021-07-17 13:20 35 ****************
7 2021-07-17 13:25 34 ***************
8 2021-07-17 13:30 34 ***************
9 2021-07-17 13:35 34 ***************
10 2021-07-17 13:40 33 **************
... ..( 6 skipped). .. **************
17 2021-07-17 14:15 33 **************
18 2021-07-17 14:20 32 *************
... ..( 21 skipped). .. *************
40 2021-07-17 16:10 32 *************
41 2021-07-17 16:15 31 ************
42 2021-07-17 16:20 32 *************
... ..( 3 skipped). .. *************
46 2021-07-17 16:40 32 *************
47 2021-07-17 16:45 31 ************
... ..( 15 skipped). .. ************
63 2021-07-17 18:05 31 ************
64 2021-07-17 18:10 32 *************
65 2021-07-17 18:15 31 ************
... ..( 7 skipped). .. ************
73 2021-07-17 18:55 31 ************
74 2021-07-17 19:00 34 ***************
75 2021-07-17 19:05 34 ***************
76 2021-07-17 19:10 35 ****************
... ..( 6 skipped). .. ****************
83 2021-07-17 19:45 35 ****************
84 2021-07-17 19:50 34 ***************
... ..( 5 skipped). .. ***************
90 2021-07-17 20:20 34 ***************
91 2021-07-17 20:25 33 **************
92 2021-07-17 20:30 32 *************
93 2021-07-17 20:35 32 *************
94 2021-07-17 20:40 32 *************
95 2021-07-17 20:45 31 ************
... ..( 6 skipped). .. ************
102 2021-07-17 21:20 31 ************
103 2021-07-17 21:25 32 *************
... ..( 10 skipped). .. *************
114 2021-07-17 22:20 32 *************
115 2021-07-17 22:25 33 **************
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 4 0 Command failed due to ICRC error
0x0002 4 0 R_ERR response for data FIS
0x0003 4 0 R_ERR response for device-to-host data FIS
0x0004 4 0 R_ERR response for host-to-device data FIS
0x0005 4 0 R_ERR response for non-data FIS
0x0006 4 0 R_ERR response for device-to-host non-data FIS
0x0007 4 0 R_ERR response for host-to-device non-data FIS
0x0008 4 0 Device-to-host non-data FIS retries
0x0009 4 714 Transition from drive PhyRdy to drive PhyNRdy
0x000a 4 714 Device-to-host register FISes sent due to a COMRESET
0x000b 4 0 CRC errors within host-to-device FIS
0x000d 4 0 Non-CRC errors within host-to-device FIS
0x000f 4 0 R_ERR response for host-to-device data FIS, CRC
0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC
0x8e00 4 0 Vendor specific
0x8e01 4 0 Vendor specific
0x8e02 4 0 Vendor specific
0x8e03 4 0 Vendor specific
0x8e04 4 0 Vendor specific
0x8e05 4 0 Vendor specific
0x8e06 4 0 Vendor specific
0x8e07 4 0 Vendor specific
0x8e08 4 0 Vendor specific
0x8e09 4 0 Vendor specific
0x8e0a 4 0 Vendor specific
0x8e0b 4 0 Vendor specific
0x8e0c 4 0 Vendor specific
0x8e0d 4 0 Vendor specific
0x8e0e 4 0 Vendor specific
0x8e0f 4 0 Vendor specific
0x8e10 4 0 Vendor specific
0x8e11 4 0 Vendor specific
More information about the Smartmontools-support
mailing list