[smartmontools-support] smartctl -l pending sample output (was: no subject)
Poovathoor, Thomas K
Poovathoor at uthscsa.edu
Fri Nov 2 15:21:11 CET 2018
I am not sure about the 197 198 referece you made. Here I paste the full output from both Toshiba and smartctl -xa output.
cosd2:~ # tsbdrv smart errors sdm
::Comprehensive error information '/dev/sdm'::
Total : 99
-------------------------------------------------------------
Error counter 1
ATA Status
Transport : 0x0
Error : 0x40
Count : 0x1
LBA : 0x39e3821b6
Device : 0xee
Status : 0x51
Device State : Active/Idle
Life timestamp (Hours) : 6206
Previous command 1
Device Control : 0x0
Feature : 0x0
Count : 0x1
LBA : 0x39e3821b6
Device : 0xe0
Command (OpCode) : 0x24
Timestamp (milliseconds) : 341692
Previous command 2
Device Control : 0x0
Feature : 0x0
Count : 0x0
LBA : 0x0
Device : 0x0
Command (OpCode) : 0xe5
Timestamp (milliseconds) : 341679
Previous command 3
Device Control : 0x0
Feature : 0x0
Count : 0x1
LBA : 0x39e3821b5
Device : 0xe0
Command (OpCode) : 0x24
Timestamp (milliseconds) : 341676
Previous command 4
Device Control : 0x0
Feature : 0x0
Count : 0x0
LBA : 0x0
Device : 0x0
Command (OpCode) : 0xe5
Timestamp (milliseconds) : 341646
Previous command 5
Device Control : 0x0
Feature : 0x0
Count : 0x1
LBA : 0x39e3821b4
Device : 0xe0
Command (OpCode) : 0x24
Timestamp (milliseconds) : 341643
Command return code: 0x00000000 [Command completed successfully]
cosd2:~ # smartctl -xa /dev/sdm
smartctl 6.6 2017-11-05 r4594 [x86_64-linux-4.4.143-94.47-default] (SUSE RPM)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: TOSHIBA MG05ACA800E
Serial Number: 97A2K8GBF96F
LU WWN Device Id: 5 000039 80b7812c3
Firmware Version: GX2A
User Capacity: 8,001,563,222,016 bytes [8.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-3 T13/2161-D revision 5
SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Fri Nov 2 09:16:50 2018 CDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 128 (minimum power consumption without standby)
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Disabled
ATA Security is: Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 772) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 0
2 Throughput_Performance P-S--- 100 100 050 - 0
3 Spin_Up_Time POS--K 100 100 001 - 7207
4 Start_Stop_Count -O--CK 100 100 000 - 25
5 Reallocated_Sector_Ct PO--CK 100 100 050 - 0
7 Seek_Error_Rate PO-R-- 100 100 050 - 0
8 Seek_Time_Performance P-S--- 100 100 050 - 0
9 Power_On_Hours -O--CK 085 085 000 - 6277
10 Spin_Retry_Count PO--CK 100 100 030 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 25
191 G-Sense_Error_Rate -O--CK 100 100 000 - 0
192 Power-Off_Retract_Count -O--CK 100 100 000 - 18
193 Load_Cycle_Count -O--CK 100 100 000 - 2085
194 Temperature_Celsius -O---K 100 100 000 - 21 (Min/Max 15/38)
196 Reallocated_Event_Count -O--CK 100 100 000 - 0
197 Current_Pending_Sector -O--CK 100 100 000 - 0
198 Offline_Uncorrectable ----CK 100 100 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 253 000 - 0
220 Disk_Shift -O---- 100 100 000 - 0
222 Loaded_Hours -O--CK 086 086 000 - 5863
223 Load_Retry_Count -O--CK 100 100 000 - 0
224 Load_Friction -O---K 100 100 000 - 0
226 Load-in_Time -OS--K 100 100 000 - 633
240 Head_Flying_Hours P----- 100 100 001 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 51 Comprehensive SMART error log
0x03 GPL R/O 64 Ext. Comprehensive SMART error log
0x04 GPL,SL R/O 8 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x08 GPL R/O 2 Power Conditions log
0x09 SL R/W 1 Selective self-test log
0x0a GPL R/W 2 Device Statistics Notification
0x0c GPL R/O 2048 Pending Defects log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x24 GPL R/O 16384 Current Device Internal Status Data log
0x25 GPL R/O 16384 Saved Device Internal Status Data log
0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa7 GPL VS 8 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (64 sectors)
Device Error Count: 99
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 99 [98] occurred at disk power-on lifetime: 6206 hours (258 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 01 00 03 9e 38 21 b6 ee 00 Error: UNC at LBA = 0x39e3821b6 = 15539380662
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
24 00 00 00 01 00 03 9e 38 21 b6 e0 00 1d+00:17:53.239 READ SECTOR(S) EXT
e5 00 00 00 00 00 00 00 00 00 00 00 00 1d+00:17:49.827 CHECK POWER MODE
24 00 00 00 01 00 03 9e 38 21 b5 e0 00 1d+00:17:49.239 READ SECTOR(S) EXT
e5 00 00 00 00 00 00 00 00 00 00 00 00 1d+00:17:41.426 CHECK POWER MODE
24 00 00 00 01 00 03 9e 38 21 b4 e0 00 1d+00:17:40.832 READ SECTOR(S) EXT
Error 98 [97] occurred at disk power-on lifetime: 6206 hours (258 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 01 00 03 9e 38 21 b5 ee 00 Error: UNC at LBA = 0x39e3821b5 = 15539380661
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
24 00 00 00 01 00 03 9e 38 21 b5 e0 00 1d+00:17:49.239 READ SECTOR(S) EXT
e5 00 00 00 00 00 00 00 00 00 00 00 00 1d+00:17:41.426 CHECK POWER MODE
24 00 00 00 01 00 03 9e 38 21 b4 e0 00 1d+00:17:40.832 READ SECTOR(S) EXT
e5 00 00 00 00 00 00 00 00 00 00 00 00 1d+00:17:26.570 CHECK POWER MODE
24 00 00 00 01 00 03 9e 38 21 b3 e0 00 1d+00:17:25.983 READ SECTOR(S) EXT
Error 97 [96] occurred at disk power-on lifetime: 6206 hours (258 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 01 00 03 9e 38 21 b4 ee 00 Error: UNC at LBA = 0x39e3821b4 = 15539380660
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
24 00 00 00 01 00 03 9e 38 21 b4 e0 00 1d+00:17:40.832 READ SECTOR(S) EXT
e5 00 00 00 00 00 00 00 00 00 00 00 00 1d+00:17:26.570 CHECK POWER MODE
24 00 00 00 01 00 03 9e 38 21 b3 e0 00 1d+00:17:25.983 READ SECTOR(S) EXT
e5 00 00 00 00 00 00 00 00 00 00 00 00 1d+00:17:21.618 CHECK POWER MODE
24 00 00 00 01 00 03 9e 38 21 b2 e0 00 1d+00:17:21.033 READ SECTOR(S) EXT
Error 96 [95] occurred at disk power-on lifetime: 6206 hours (258 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 01 00 03 9e 38 21 b3 ee 00 Error: UNC at LBA = 0x39e3821b3 = 15539380659
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
24 00 00 00 01 00 03 9e 38 21 b3 e0 00 1d+00:17:25.983 READ SECTOR(S) EXT
e5 00 00 00 00 00 00 00 00 00 00 00 00 1d+00:17:21.618 CHECK POWER MODE
24 00 00 00 01 00 03 9e 38 21 b2 e0 00 1d+00:17:21.033 READ SECTOR(S) EXT
e5 00 00 00 00 00 00 00 00 00 00 00 00 1d+00:17:05.418 CHECK POWER MODE
24 00 00 00 01 00 03 9e 38 21 b1 e0 00 1d+00:17:04.832 READ SECTOR(S) EXT
Error 95 [94] occurred at disk power-on lifetime: 6206 hours (258 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 01 00 03 9e 38 21 b2 ee 00 Error: UNC at LBA = 0x39e3821b2 = 15539380658
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
24 00 00 00 01 00 03 9e 38 21 b2 e0 00 1d+00:17:21.033 READ SECTOR(S) EXT
e5 00 00 00 00 00 00 00 00 00 00 00 00 1d+00:17:05.418 CHECK POWER MODE
24 00 00 00 01 00 03 9e 38 21 b1 e0 00 1d+00:17:04.832 READ SECTOR(S) EXT
e5 00 00 00 00 00 00 00 00 00 00 00 00 1d+00:16:58.947 CHECK POWER MODE
24 00 00 00 01 00 03 9e 38 21 b0 e0 00 1d+00:16:58.928 READ SECTOR(S) EXT
Error 94 [93] occurred at disk power-on lifetime: 6206 hours (258 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 01 00 03 9e 38 21 b1 ee 00 Error: UNC at LBA = 0x39e3821b1 = 15539380657
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
24 00 00 00 01 00 03 9e 38 21 b1 e0 00 1d+00:17:04.832 READ SECTOR(S) EXT
e5 00 00 00 00 00 00 00 00 00 00 00 00 1d+00:16:58.947 CHECK POWER MODE
24 00 00 00 01 00 03 9e 38 21 b0 e0 00 1d+00:16:58.928 READ SECTOR(S) EXT
e5 00 00 00 00 00 00 00 00 00 00 00 00 1d+00:16:46.726 CHECK POWER MODE
2f 00 00 00 01 00 00 00 00 00 0c 00 00 1d+00:16:46.636 READ LOG EXT
Error 93 [92] occurred at disk power-on lifetime: 6204 hours (258 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 41 00 00 00 03 9e 38 21 b0 40 00 Error: WP at LBA = 0x39e3821b0 = 15539380656
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 04 00 00 08 00 01 0e 6a 0f 00 40 00 22:50:01.856 WRITE FPDMA QUEUED
60 04 00 00 00 00 03 9e 38 1f 00 40 00 22:49:59.051 READ FPDMA QUEUED
60 04 00 00 00 00 02 ab 58 85 00 40 00 22:49:59.049 READ FPDMA QUEUED
60 04 00 00 00 00 02 ab 58 81 00 40 00 22:49:59.032 READ FPDMA QUEUED
60 04 00 00 00 00 01 96 05 9d 00 40 00 22:49:59.028 READ FPDMA QUEUED
Error 92 [91] occurred at disk power-on lifetime: 6199 hours (258 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 41 00 00 00 03 9e 38 21 b0 40 00 Error: UNC at LBA = 0x39e3821b0 = 15539380656
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 04 00 00 00 00 03 9e 38 1f 00 40 00 17:49:56.841 READ FPDMA QUEUED
60 04 00 00 00 00 02 ab 58 85 00 40 00 17:49:56.838 READ FPDMA QUEUED
60 04 00 00 00 00 02 ab 58 81 00 40 00 17:49:56.821 READ FPDMA QUEUED
60 04 00 00 00 00 01 96 05 9d 00 40 00 17:49:56.818 READ FPDMA QUEUED
60 04 00 00 00 00 01 96 05 99 00 40 00 17:49:56.801 READ FPDMA QUEUED
SMART Error Log Version: 1
ATA Error Count: 99 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 99 occurred at disk power-on lifetime: 6206 hours (258 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 b6 21 38 ee Error: UNC at LBA = 0x0e3821b6 = 238559670
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
24 00 01 b6 21 38 e0 00 1d+00:17:53.239 READ SECTOR(S) EXT
e5 00 00 00 00 00 00 00 1d+00:17:49.827 CHECK POWER MODE
24 00 01 b5 21 38 e0 00 1d+00:17:49.239 READ SECTOR(S) EXT
e5 00 00 00 00 00 00 00 1d+00:17:41.426 CHECK POWER MODE
24 00 01 b4 21 38 e0 00 1d+00:17:40.832 READ SECTOR(S) EXT
Error 98 occurred at disk power-on lifetime: 6206 hours (258 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 b5 21 38 ee Error: UNC at LBA = 0x0e3821b5 = 238559669
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
24 00 01 b5 21 38 e0 00 1d+00:17:49.239 READ SECTOR(S) EXT
e5 00 00 00 00 00 00 00 1d+00:17:41.426 CHECK POWER MODE
24 00 01 b4 21 38 e0 00 1d+00:17:40.832 READ SECTOR(S) EXT
e5 00 00 00 00 00 00 00 1d+00:17:26.570 CHECK POWER MODE
24 00 01 b3 21 38 e0 00 1d+00:17:25.983 READ SECTOR(S) EXT
Error 97 occurred at disk power-on lifetime: 6206 hours (258 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 b4 21 38 ee Error: UNC at LBA = 0x0e3821b4 = 238559668
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
24 00 01 b4 21 38 e0 00 1d+00:17:40.832 READ SECTOR(S) EXT
e5 00 00 00 00 00 00 00 1d+00:17:26.570 CHECK POWER MODE
24 00 01 b3 21 38 e0 00 1d+00:17:25.983 READ SECTOR(S) EXT
e5 00 00 00 00 00 00 00 1d+00:17:21.618 CHECK POWER MODE
24 00 01 b2 21 38 e0 00 1d+00:17:21.033 READ SECTOR(S) EXT
Error 96 occurred at disk power-on lifetime: 6206 hours (258 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 b3 21 38 ee Error: UNC at LBA = 0x0e3821b3 = 238559667
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
24 00 01 b3 21 38 e0 00 1d+00:17:25.983 READ SECTOR(S) EXT
e5 00 00 00 00 00 00 00 1d+00:17:21.618 CHECK POWER MODE
24 00 01 b2 21 38 e0 00 1d+00:17:21.033 READ SECTOR(S) EXT
e5 00 00 00 00 00 00 00 1d+00:17:05.418 CHECK POWER MODE
24 00 01 b1 21 38 e0 00 1d+00:17:04.832 READ SECTOR(S) EXT
Error 95 occurred at disk power-on lifetime: 6206 hours (258 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 b2 21 38 ee Error: UNC at LBA = 0x0e3821b2 = 238559666
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
24 00 01 b2 21 38 e0 00 1d+00:17:21.033 READ SECTOR(S) EXT
e5 00 00 00 00 00 00 00 1d+00:17:05.418 CHECK POWER MODE
24 00 01 b1 21 38 e0 00 1d+00:17:04.832 READ SECTOR(S) EXT
e5 00 00 00 00 00 00 00 1d+00:16:58.947 CHECK POWER MODE
24 00 01 b0 21 38 e0 00 1d+00:16:58.928 READ SECTOR(S) EXT
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 5661 -
# 2 Extended offline Completed without error 00% 4821 -
# 3 Extended offline Completed without error 00% 4146 -
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 5661 -
# 2 Extended offline Completed without error 00% 4821 -
# 3 Extended offline Completed without error 00% 4146 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 1 (0x0001)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 21 Celsius
Power Cycle Min/Max Temperature: 20/26 Celsius
Lifetime Min/Max Temperature: 15/38 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 5/55 Celsius
Min/Max Temperature Limit: 5/55 Celsius
Temperature History Size (Index): 478 (140)
Index Estimated Time Temperature Celsius
141 2018-11-02 01:19 20 *
... ..( 5 skipped). .. *
147 2018-11-02 01:25 20 *
148 2018-11-02 01:26 21 **
... ..( 14 skipped). .. **
163 2018-11-02 01:41 21 **
164 2018-11-02 01:42 20 *
... ..( 5 skipped). .. *
170 2018-11-02 01:48 20 *
171 2018-11-02 01:49 21 **
... ..( 25 skipped). .. **
197 2018-11-02 02:15 21 **
198 2018-11-02 02:16 20 *
... ..( 6 skipped). .. *
205 2018-11-02 02:23 20 *
206 2018-11-02 02:24 21 **
... ..( 19 skipped). .. **
226 2018-11-02 02:44 21 **
227 2018-11-02 02:45 20 *
228 2018-11-02 02:46 21 **
... ..( 30 skipped). .. **
259 2018-11-02 03:17 21 **
260 2018-11-02 03:18 20 *
... ..( 3 skipped). .. *
264 2018-11-02 03:22 20 *
265 2018-11-02 03:23 21 **
... ..( 20 skipped). .. **
286 2018-11-02 03:44 21 **
287 2018-11-02 03:45 20 *
288 2018-11-02 03:46 20 *
289 2018-11-02 03:47 21 **
... ..( 27 skipped). .. **
317 2018-11-02 04:15 21 **
318 2018-11-02 04:16 20 *
... ..( 7 skipped). .. *
326 2018-11-02 04:24 20 *
327 2018-11-02 04:25 21 **
... ..( 17 skipped). .. **
345 2018-11-02 04:43 21 **
346 2018-11-02 04:44 20 *
347 2018-11-02 04:45 20 *
348 2018-11-02 04:46 20 *
349 2018-11-02 04:47 21 **
... ..( 28 skipped). .. **
378 2018-11-02 05:16 21 **
379 2018-11-02 05:17 20 *
... ..( 5 skipped). .. *
385 2018-11-02 05:23 20 *
386 2018-11-02 05:24 21 **
... ..( 19 skipped). .. **
406 2018-11-02 05:44 21 **
407 2018-11-02 05:45 20 *
408 2018-11-02 05:46 20 *
409 2018-11-02 05:47 21 **
... ..( 26 skipped). .. **
436 2018-11-02 06:14 21 **
437 2018-11-02 06:15 20 *
... ..( 8 skipped). .. *
446 2018-11-02 06:24 20 *
447 2018-11-02 06:25 21 **
... ..( 17 skipped). .. **
465 2018-11-02 06:43 21 **
466 2018-11-02 06:44 20 *
... ..( 2 skipped). .. *
469 2018-11-02 06:47 20 *
470 2018-11-02 06:48 21 **
... ..( 23 skipped). .. **
16 2018-11-02 07:12 21 **
17 2018-11-02 07:13 20 *
... ..( 13 skipped). .. *
31 2018-11-02 07:27 20 *
32 2018-11-02 07:28 21 **
... ..( 11 skipped). .. **
44 2018-11-02 07:40 21 **
45 2018-11-02 07:41 20 *
... ..( 7 skipped). .. *
53 2018-11-02 07:49 20 *
54 2018-11-02 07:50 21 **
... ..( 26 skipped). .. **
81 2018-11-02 08:17 21 **
82 2018-11-02 08:18 20 *
83 2018-11-02 08:19 21 **
84 2018-11-02 08:20 21 **
85 2018-11-02 08:21 20 *
86 2018-11-02 08:22 20 *
87 2018-11-02 08:23 21 **
... ..( 20 skipped). .. **
108 2018-11-02 08:44 21 **
109 2018-11-02 08:45 20 *
110 2018-11-02 08:46 21 **
... ..( 29 skipped). .. **
140 2018-11-02 09:16 21 **
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
Device Statistics (GP Log 0x04)
Page Offset Size Value Flags Description
0x01 ===== = = === == General Statistics (rev 1) ==
0x01 0x008 4 25 --- Lifetime Power-On Resets
0x01 0x010 4 6277 --- Power-on Hours
0x01 0x018 6 25812735226 --- Logical Sectors Written
0x01 0x020 6 29169738 --- Number of Write Commands
0x01 0x028 6 283204566837 --- Logical Sectors Read
0x01 0x030 6 1405188667 --- Number of Read Commands
0x01 0x038 6 22599194042 --- Date and Time TimeStamp
0x02 ===== = = === == Free-Fall Statistics (rev 1) ==
0x02 0x010 4 0 --- Overlimit Shock Events
0x03 ===== = = === == Rotating Media Statistics (rev 1) ==
0x03 0x008 4 6277 --- Spindle Motor Power-on Hours
0x03 0x010 4 5863 --- Head Flying Hours
0x03 0x018 4 2085 --- Head Load Events
0x03 0x020 4 0 -D- Number of Reallocated Logical Sectors
0x03 0x028 4 6 --- Read Recovery Attempts
0x03 0x030 4 0 --- Number of Mechanical Start Failures
0x03 0x038 4 0 --- Number of Realloc. Candidate Logical Sectors
0x03 0x040 4 18 --- Number of High Priority Unload Events
0x04 ===== = = === == General Errors Statistics (rev 1) ==
0x04 0x008 4 99 --- Number of Reported Uncorrectable Errors
0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion
0x05 ===== = = === == Temperature Statistics (rev 1) ==
0x05 0x008 1 21 --- Current Temperature
0x05 0x010 1 21 N-- Average Short Term Temperature
0x05 0x018 1 21 N-- Average Long Term Temperature
0x05 0x020 1 38 --- Highest Temperature
0x05 0x028 1 15 --- Lowest Temperature
0x05 0x030 1 26 N-- Highest Average Short Term Temperature
0x05 0x038 1 19 N-- Lowest Average Short Term Temperature
0x05 0x040 1 22 N-- Highest Average Long Term Temperature
0x05 0x048 1 20 N-- Lowest Average Long Term Temperature
0x05 0x050 4 0 --- Time in Over-Temperature
0x05 0x058 1 55 --- Specified Maximum Operating Temperature
0x05 0x060 4 0 --- Time in Under-Temperature
0x05 0x068 1 5 --- Specified Minimum Operating Temperature
0x06 ===== = = === == Transport Statistics (rev 1) ==
0x06 0x008 4 0 --- Number of Hardware Resets
0x06 0x010 4 23 --- Number of ASR Events
0x06 0x018 4 0 --- Number of Interface CRC Errors
0x07 ===== = = === == Solid State Device Statistics (rev 1) ==
|||_ C monitored condition met
||__ D supports DSN
|___ N normalized value
Pending Defects log (GP Log 0x0c) supported [please try: '-l defects']
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 4 0 Command failed due to ICRC error
0x0002 4 0 R_ERR response for data FIS
0x0003 4 0 R_ERR response for device-to-host data FIS
0x0004 4 0 R_ERR response for host-to-device data FIS
0x0005 4 0 R_ERR response for non-data FIS
0x0006 4 0 R_ERR response for device-to-host non-data FIS
0x0007 4 0 R_ERR response for host-to-device non-data FIS
0x0008 4 0 Device-to-host non-data FIS retries
0x0009 4 0 Transition from drive PhyRdy to drive PhyNRdy
0x000a 4 0 Device-to-host register FISes sent due to a COMRESET
0x000b 4 0 CRC errors within host-to-device FIS
0x000d 4 0 Non-CRC errors within host-to-device FIS
0x000f 4 0 R_ERR response for host-to-device data FIS, CRC
0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC
cosd2:~ #
Thank You!
Tom
Service Requests:
https://uthscsa.teamdynamix.com/TDClient/Requests/ServiceDet?ID=25357
-----Original Message-----
From: Christian Franke <Christian.Franke at t-online.de>
Sent: Friday, November 02, 2018 5:25 AM
To: Poovathoor, Thomas K <Poovathoor at uthscsa.edu>
Cc: smartmontools-support at listi.jpberlin.de
Subject: Re: [smartmontools-support] smartctl -l pending sample output (was: no subject)
Thomas K Poovathoor wrote:
>
> cosd2:~ # smartctl -l defects /dev/sdm
>
> smartctl 6.6 2017-11-05 r4594 [x86_64-linux-4.4.143-94.47-default]
> (SUSE RPM)
>
> Copyright (C) 2002-17, Bruce Allen, Christian Franke,
> www.smartmontools.org
>
> Pending Defects log (GP Log 0x0c)
>
> Index LBA Hours
>
> 0 15539380656 -
>
> 1 15539380657 -
>
> 2 15539380658 -
>
> 3 15539380659 -
>
> 4 15539380660 -
>
> 5 15539380661 -
>
> 6 15539380662 -
>
> 7 15539380663 -
>
> Please send sample output of above table to:
>
> smartmontools-support at listi.jpberlin.de
>
Thanks for providing the first real world test case for the '-l defects'
option. This new ATA feature is still not widely supported and therefore devices with non-empty logs are rare.
The output looks reasonable under the assumption that the disk capacity is at least 8TB. The empty "Hours" column is OK as this info is optional.
Is the raw value of SMART attribute 197 (or 198) identical to the count of listed pending defects?
Thanks,
Christian
More information about the Smartmontools-support
mailing list