smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-66-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: TOSHIBA THNSNJ480PCSZ Serial Number: 45FS109KTM7W LU WWN Device Id: 5 00080d 91037daa6 Firmware Version: JZET6102 User Capacity: 480.103.981.056 bytes [480 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-3 (minor revision not indicated) SATA Version is: SATA 3.2, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Mon Mar 1 10:31:09 2021 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 19) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate -O-R-- 100 100 000 - 0 2 Throughput_Performance P-S--- 100 100 050 - 0 3 Spin_Up_Time POS--- 100 100 050 - 0 5 Reallocated_Sector_Ct PO--C- 100 100 050 - 0 7 Unknown_SSD_Attribute PO-R-- 100 100 050 - 0 8 Unknown_SSD_Attribute P-S--- 100 100 050 - 0 9 Power_On_Hours -O--C- 100 100 000 - 13179 10 Unknown_SSD_Attribute PO--C- 100 100 050 - 0 12 Power_Cycle_Count -O--C- 100 100 000 - 904 167 Unknown_Attribute -O---K 100 100 000 - 0 168 Unknown_Attribute -O--C- 100 100 000 - 21 169 Unknown_Attribute PO--C- 100 100 010 - 100 170 Unknown_Attribute PO--C- 100 100 010 - 0 173 Unknown_Attribute -O--C- 200 200 000 - 480853 174 Unknown_Attribute -O--C- 200 200 000 - 1651910 175 Program_Fail_Count_Chip PO--C- 100 100 010 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--C- 100 100 000 - 18 194 Temperature_Celsius -O---K 071 053 000 - 29 (Min/Max 11/47) 197 Current_Pending_Sector -O--C- 100 100 000 - 0 232 Available_Reservd_Space -O---K 100 100 000 - 0 240 Unknown_SSD_Attribute PO--C- 100 100 050 - 0 241 Total_LBAs_Written -O--C- 100 100 000 - 114278 242 Total_LBAs_Read -O--C- 100 100 000 - 138245 243 Unknown_Attribute -O--C- 100 100 000 - 10 249 Unknown_Attribute -O---K 100 100 000 - 11878 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 21 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 21 [20] occurred at disk power-on lifetime: 4289 hours (178 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ff ff ff ff ff ff ff ff ff ff ff ff ff 00:06:53.578 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:06:53.578 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:06:53.578 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:06:53.578 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:06:53.578 [VENDOR SPECIFIC] Error 20 [19] occurred at disk power-on lifetime: 4289 hours (178 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ff ff ff ff ff ff ff ff ff ff ff ff ff 00:06:32.369 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:06:32.369 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:06:32.369 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:06:32.369 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:06:32.369 [VENDOR SPECIFIC] Error 19 [18] occurred at disk power-on lifetime: 4112 hours (171 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ff ff ff ff ff ff ff ff ff ff ff ff ff 00:10:18.226 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:10:18.226 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:10:18.226 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:10:18.226 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:10:18.226 [VENDOR SPECIFIC] Error 18 [17] occurred at disk power-on lifetime: 4112 hours (171 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ff ff ff ff ff ff ff ff ff ff ff ff ff 00:09:58.111 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:09:58.111 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:09:58.111 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:09:58.111 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:09:58.111 [VENDOR SPECIFIC] Error 17 [16] occurred at disk power-on lifetime: 4112 hours (171 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ff ff ff ff ff ff ff ff ff ff ff ff ff 00:09:52.783 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:09:52.782 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:09:52.782 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:09:52.782 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:09:52.782 [VENDOR SPECIFIC] Error 16 [15] occurred at disk power-on lifetime: 4112 hours (171 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ff ff ff ff ff ff ff ff ff ff ff ff ff 00:09:39.365 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:09:39.365 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:09:39.365 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:09:39.365 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:09:39.365 [VENDOR SPECIFIC] Error 15 [14] occurred at disk power-on lifetime: 2692 hours (112 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ff ff ff ff ff ff ff ff ff ff ff ff ff 00:06:55.246 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:06:55.246 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:06:55.246 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:06:55.246 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:06:55.246 [VENDOR SPECIFIC] Error 14 [13] occurred at disk power-on lifetime: 2692 hours (112 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ff ff ff ff ff ff ff ff ff ff ff ff ff 00:06:47.148 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:06:47.148 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:06:47.148 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:06:47.148 [VENDOR SPECIFIC] ff ff ff ff ff ff ff ff ff ff ff ff ff 00:06:47.148 [VENDOR SPECIFIC] SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 13179 - # 2 Extended offline Completed without error 00% 13177 - # 3 Short offline Completed without error 00% 13177 - # 4 Short offline Completed without error 00% 7491 - # 5 Short offline Completed without error 00% 11 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 3 (0x0003) Device State: Active (0) Current Temperature: 29 Celsius Power Cycle Min/Max Temperature: 21/34 Celsius Lifetime Min/Max Temperature: 11/47 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 00 00 04 00 01 01 00 05 05 00 00 00 00 00 00 00 00 02 00 00 97 f4 d3 02 04 04 00 00 00 00 00 07 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/40 Celsius Min/Max Temperature Limit: 0/80 Celsius Temperature History Size (Index): 128 (95) Index Estimated Time Temperature Celsius 96 2021-03-01 08:24 25 ****** 97 2021-03-01 08:25 25 ****** 98 2021-03-01 08:26 26 ******* 99 2021-03-01 08:27 29 ********** 100 2021-03-01 08:28 29 ********** 101 2021-03-01 08:29 27 ******** 102 2021-03-01 08:30 27 ******** 103 2021-03-01 08:31 26 ******* ... ..( 4 skipped). .. ******* 108 2021-03-01 08:36 26 ******* 109 2021-03-01 08:37 29 ********** 110 2021-03-01 08:38 30 *********** 111 2021-03-01 08:39 31 ************ 112 2021-03-01 08:40 32 ************* 113 2021-03-01 08:41 32 ************* 114 2021-03-01 08:42 33 ************** 115 2021-03-01 08:43 33 ************** 116 2021-03-01 08:44 33 ************** 117 2021-03-01 08:45 34 *************** ... ..( 2 skipped). .. *************** 120 2021-03-01 08:48 34 *************** 121 2021-03-01 08:49 30 *********** 122 2021-03-01 08:50 29 ********** 123 2021-03-01 08:51 28 ********* 124 2021-03-01 08:52 28 ********* 125 2021-03-01 08:53 27 ******** 126 2021-03-01 08:54 27 ******** 127 2021-03-01 08:55 27 ******** 0 2021-03-01 08:56 26 ******* ... ..( 91 skipped). .. ******* 92 2021-03-01 10:28 26 ******* 93 2021-03-01 10:29 27 ******** 94 2021-03-01 10:30 30 *********** 95 2021-03-01 10:31 30 *********** SCT Error Recovery Control: Read: 600 (60,0 seconds) Write: 600 (60,0 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 904 --- Lifetime Power-On Resets 0x01 0x018 6 7489352129 --- Logical Sectors Written 0x01 0x020 6 106871456 --- Number of Write Commands 0x01 0x028 6 9060028453 --- Logical Sectors Read 0x01 0x030 6 168346202 --- Number of Read Commands 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 29 --- Current Temperature 0x05 0x010 1 26 --- Average Short Term Temperature 0x05 0x018 1 25 --- Average Long Term Temperature 0x05 0x020 1 38 --- Highest Temperature 0x05 0x028 1 18 --- Lowest Temperature 0x05 0x030 1 35 --- Highest Average Short Term Temperature 0x05 0x038 1 21 --- Lowest Average Short Term Temperature 0x05 0x040 1 32 --- Highest Average Long Term Temperature 0x05 0x048 1 24 --- Lowest Average Long Term Temperature 0x05 0x050 4 590 --- Time in Over-Temperature 0x05 0x058 1 40 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 5 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 1780 --- Number of Hardware Resets 0x06 0x018 4 21 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 12 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 13 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC