<html><head></head><body><div style="font-family: Verdana;font-size: 12.0px;"><div>dmesg:</div>
<div> </div>
<div>[usb.002.003] /sys/devices/pci0000:00/0000:00:14.0/usb2/2-4 added</div>
<div>scsi 15:0:0:0: Direct-Access ADATA HV100 9201 PQ: 0 ANSI: 6</div>
<div>sd 15:0:0:0: Attached scsi generic sg5 type 0<br/>
1953525168 512-byte logical blocks: (1.00 TB/932 GiB)</div>
<div>Write Protect is off</div>
<div>Mode Sense: 47 00 00 08</div>
<div>Write cache: enabled, read cache: enabled, doesn't support DPO or FUA</div>
<div>Attached SCSI disk</div>
<div> </div>
<div> </div>
<div>lsusb:</div>
<div> </div>
<div>Bus 002 Device 003: ID 125f:a42a</div>
<div> </div>
<div> </div>
<div> </div>
<div>[/] # smartctl -d sat -q noserial -a /dev/sdf</div>
<div>
<div>smartctl 7.1 2019-12-30 r5022 [x86_64-linux] (localbuild)<br/>
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org</div>
<div>=== START OF INFORMATION SECTION ===<br/>
Device Model: ST1000LM035-1RK172<br/>
Firmware Version: SBM3<br/>
User Capacity: 1,000,204,886,016 bytes [1.00 TB]<br/>
Sector Sizes: 512 bytes logical, 4096 bytes physical<br/>
Rotation Rate: 5400 rpm<br/>
Form Factor: 2.5 inches<br/>
Device is: Not in smartctl database [for details use: -P showall]<br/>
ATA Version is: ACS-3 T13/2161-D revision 3b<br/>
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)<br/>
Local Time is: Mon May 4 18:28:30 2020 CEST<br/>
SMART support is: Available - device has SMART capability.<br/>
SMART support is: Enabled</div>
<div>=== START OF READ SMART DATA SECTION ===<br/>
SMART Status not supported: Incomplete response, ATA output registers missing<br/>
SMART overall-health self-assessment test result: PASSED<br/>
Warning: This result is based on an Attribute check.</div>
<div>General SMART Values:<br/>
Offline data collection status: (0x00) Offline data collection activity<br/>
was never started.<br/>
Auto Offline Data Collection: Disabled.<br/>
Self-test execution status: ( 0) The previous self-test routine completed<br/>
without error or no self-test has ever <br/>
been run.<br/>
Total time to complete Offline <br/>
data collection: ( 0) seconds.<br/>
Offline data collection<br/>
capabilities: (0x71) SMART execute Offline immediate.<br/>
No Auto Offline data collection support.<br/>
Suspend Offline collection upon new<br/>
command.<br/>
No Offline surface scan supported.<br/>
Self-test supported.<br/>
Conveyance Self-test supported.<br/>
Selective Self-test supported.<br/>
SMART capabilities: (0x0003) Saves SMART data before entering<br/>
power-saving mode.<br/>
Supports SMART auto save timer.<br/>
Error logging capability: (0x01) Error logging supported.<br/>
General Purpose Logging supported.<br/>
Short self-test routine <br/>
recommended polling time: ( 1) minutes.<br/>
Extended self-test routine<br/>
recommended polling time: ( 168) minutes.<br/>
Conveyance self-test routine<br/>
recommended polling time: ( 2) minutes.<br/>
SCT capabilities: (0x3035) SCT Status supported.<br/>
SCT Feature Control supported.<br/>
SCT Data Table supported.</div>
<div>SMART Attributes Data Structure revision number: 10<br/>
Vendor Specific SMART Attributes with Thresholds:<br/>
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE<br/>
1 Raw_Read_Error_Rate 0x000f 083 065 006 Pre-fail Always - 191256130<br/>
3 Spin_Up_Time 0x0003 099 099 000 Pre-fail Always - 0<br/>
4 Start_Stop_Count 0x0032 099 099 020 Old_age Always - 1866<br/>
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0<br/>
7 Seek_Error_Rate 0x000f 067 060 045 Pre-fail Always - 4549808<br/>
9 Power_On_Hours 0x0032 076 076 000 Old_age Always - 21134 (20 182 0)<br/>
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0<br/>
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 95<br/>
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0<br/>
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0<br/>
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0<br/>
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0<br/>
190 Airflow_Temperature_Cel 0x0022 071 048 040 Old_age Always - 29 (Min/Max 24/29)<br/>
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 1<br/>
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 3<br/>
193 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 5433<br/>
194 Temperature_Celsius 0x0022 029 052 000 Old_age Always - 29 (0 14 0 0 0)<br/>
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0<br/>
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0<br/>
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0<br/>
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 837 (254 220 0)<br/>
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 1058817172<br/>
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 2306412423<br/>
254 Free_Fall_Sensor 0x0032 100 100 000 Old_age Always - 0</div>
<div>SMART Error Log Version: 1<br/>
No Errors Logged</div>
<div>SMART Self-test log structure revision number 1<br/>
No self-tests have been logged. [To run self-tests, use: smartctl -t]</div>
<div>SMART Selective self-test log data structure revision number 1<br/>
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS<br/>
1 0 0 Not_testing<br/>
2 0 0 Not_testing<br/>
3 0 0 Not_testing<br/>
4 0 0 Not_testing<br/>
5 0 0 Not_testing<br/>
Selective self-test flags (0x0):<br/>
After scanning selected spans, do NOT read-scan remainder of disk.<br/>
If Selective self-test is pending on power-up, resume after 0 minute delay.</div>
</div>
<div> </div></div></body></html>