smartctl 6.6 2017-11-05 r4594 [x86_64-linux-4.19.0-5-amd64] (local build) Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: SAMSUNG HD161HJ Firmware Version: GF100-07 User Capacity: 160.041.885.696 bytes [160 GB] Sector Size: 512 bytes logical/physical Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ATA8-ACS T13/1699-D revision 3b SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Wed Aug 14 00:21:21 2019 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 128 (quiet), recommended: 254 APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 2640) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 44) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 18 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 100 051 - 0 3 Spin_Up_Time POS--- 073 067 011 - 4000 4 Start_Stop_Count -O--CK 095 095 000 - 4591 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate POSR-- 252 252 051 - 0 8 Seek_Time_Performance P-S--K 090 090 015 - 4609 9 Power_On_Hours -O--CK 094 094 000 - 3168430 10 Spin_Retry_Count PO--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--C- 252 252 000 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 2331 184 End-to-End_Error -O--CK 252 252 000 - 0 187 Reported_Uncorrect -O--CK 048 048 000 - 52 188 Command_Timeout -O--CK 252 252 000 - 0 190 Airflow_Temperature_Cel -O---K 130 118 000 - 41 194 Temperature_Celsius -O---K 130 118 000 - 41 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--C- 252 099 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 200 199 000 - 0 200 Multi_Zone_Error_Rate -O-R-- 100 100 000 - 0 201 Soft_Read_Error_Rate -O-R-- 252 252 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 84 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 84 [3] occurred at disk power-on lifetime: 12770 hours (532 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 80 00 00 00 00 73 80 e0 00 Error: ICRC, ABRT 128 sectors at LBA = 0x00007380 = 29568 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 da d8 00 80 00 00 00 00 73 80 e0 00 00:02:30.000 READ DMA EXT 25 da d8 00 80 00 00 00 00 73 00 e0 00 00:02:30.000 READ DMA EXT 25 da d8 00 80 00 00 00 00 72 80 e0 00 00:02:30.000 READ DMA EXT 25 da d8 00 80 00 00 00 00 72 00 e0 00 00:02:30.000 READ DMA EXT 25 da d8 00 80 00 00 00 00 71 80 e0 00 00:02:30.000 READ DMA EXT Error 83 [2] occurred at disk power-on lifetime: 12770 hours (532 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 80 00 00 00 00 3a 80 e0 00 Error: ICRC, ABRT 128 sectors at LBA = 0x00003a80 = 14976 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 da d8 00 80 00 00 00 00 3a 80 e0 00 00:02:29.000 READ DMA EXT 25 da d8 00 80 00 00 00 00 3a 00 e0 00 00:02:29.000 READ DMA EXT 25 da d8 00 80 00 00 00 00 39 80 e0 00 00:02:29.000 READ DMA EXT 25 da d8 00 80 00 00 00 00 39 00 e0 00 00:02:29.000 READ DMA EXT 25 da d8 00 80 00 00 00 00 38 80 e0 00 00:02:29.000 READ DMA EXT Error 82 [1] occurred at disk power-on lifetime: 12770 hours (532 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 08 00 00 00 00 52 d8 e0 00 Error: ICRC, ABRT 8 sectors at LBA = 0x000052d8 = 21208 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 da d8 00 08 00 00 00 00 52 d8 e0 00 00:02:28.000 READ DMA EXT 25 da d8 00 08 00 00 00 00 52 d0 e0 00 00:02:28.000 READ DMA EXT 25 da d8 00 08 00 00 00 00 52 c8 e0 00 00:02:28.000 READ DMA EXT 25 da d8 00 08 00 00 00 00 52 c0 e0 00 00:02:28.000 READ DMA EXT 25 da d8 00 08 00 00 00 00 52 b8 e0 00 00:02:28.000 READ DMA EXT Error 81 [0] occurred at disk power-on lifetime: 12770 hours (532 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 08 00 00 00 00 43 98 e0 00 Error: ICRC, ABRT 8 sectors at LBA = 0x00004398 = 17304 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 da d8 00 08 00 00 00 00 43 98 e0 00 00:02:28.000 READ DMA EXT 25 da d8 00 08 00 00 00 00 43 90 e0 00 00:02:28.000 READ DMA EXT 25 da d8 00 08 00 00 00 00 43 88 e0 00 00:02:28.000 READ DMA EXT 25 da d8 00 08 00 00 00 00 43 80 e0 00 00:02:28.000 READ DMA EXT 25 da d8 00 08 00 00 00 00 43 78 e0 00 00:02:28.000 READ DMA EXT Error 80 [7] occurred at disk power-on lifetime: 12770 hours (532 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 80 00 00 00 00 73 80 e0 00 Error: ICRC, ABRT 128 sectors at LBA = 0x00007380 = 29568 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 da d8 00 80 00 00 00 00 73 80 e0 00 00:02:30.000 READ DMA EXT 25 da d8 00 80 00 00 00 00 73 00 e0 00 00:02:30.000 READ DMA EXT 25 da d8 00 80 00 00 00 00 72 80 e0 00 00:02:30.000 READ DMA EXT 25 da d8 00 80 00 00 00 00 72 00 e0 00 00:02:30.000 READ DMA EXT 25 da d8 00 80 00 00 00 00 71 80 e0 00 00:02:30.000 READ DMA EXT Error 79 [6] occurred at disk power-on lifetime: 12770 hours (532 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 80 00 00 00 00 3a 80 e0 00 Error: ICRC, ABRT 128 sectors at LBA = 0x00003a80 = 14976 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 da d8 00 80 00 00 00 00 3a 80 e0 00 00:02:29.000 READ DMA EXT 25 da d8 00 80 00 00 00 00 3a 00 e0 00 00:02:29.000 READ DMA EXT 25 da d8 00 80 00 00 00 00 39 80 e0 00 00:02:29.000 READ DMA EXT 25 da d8 00 80 00 00 00 00 39 00 e0 00 00:02:29.000 READ DMA EXT 25 da d8 00 80 00 00 00 00 38 80 e0 00 00:02:29.000 READ DMA EXT Error 78 [5] occurred at disk power-on lifetime: 12770 hours (532 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 08 00 00 00 00 52 d8 e0 00 Error: ICRC, ABRT 8 sectors at LBA = 0x000052d8 = 21208 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 da d8 00 08 00 00 00 00 52 d8 e0 00 00:02:28.000 READ DMA EXT 25 da d8 00 08 00 00 00 00 52 d0 e0 00 00:02:28.000 READ DMA EXT 25 da d8 00 08 00 00 00 00 52 c8 e0 00 00:02:28.000 READ DMA EXT 25 da d8 00 08 00 00 00 00 52 c0 e0 00 00:02:28.000 READ DMA EXT 25 da d8 00 08 00 00 00 00 52 b8 e0 00 00:02:28.000 READ DMA EXT Error 77 [4] occurred at disk power-on lifetime: 12770 hours (532 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 08 00 00 00 00 43 98 e0 00 Error: ICRC, ABRT 8 sectors at LBA = 0x00004398 = 17304 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 da d8 00 08 00 00 00 00 43 98 e0 00 00:02:28.000 READ DMA EXT 25 da d8 00 08 00 00 00 00 43 90 e0 00 00:02:28.000 READ DMA EXT 25 da d8 00 08 00 00 00 00 43 88 e0 00 00:02:28.000 READ DMA EXT 25 da d8 00 08 00 00 00 00 43 80 e0 00 00:02:28.000 READ DMA EXT 25 da d8 00 08 00 00 00 00 43 78 e0 00 00:02:28.000 READ DMA EXT Warning! SMART Extended Self-test Log Structure error: invalid SMART checksum. SMART Extended Self-test Log Version: 0 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Vendor (0xeb) Completed without error 00% 0 - # 2 Reserved (0x06) Completed without error 00% 0 - # 3 Offline Completed without error 00% 6 - # 4 Offline Completed without error 00% 0 - # 5 Offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 41 Celsius Power Cycle Max Temperature: 41 Celsius Lifetime Max Temperature: 41 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 10/105 Celsius Min/Max Temperature Limit: 5/110 Celsius Temperature History Size (Index): 128 (119) Index Estimated Time Temperature Celsius 120 2019-08-13 22:14 40 ********************* ... ..( 19 skipped). .. ********************* 12 2019-08-13 22:34 40 ********************* 13 2019-08-13 22:35 41 ********************** ... ..(105 skipped). .. ********************** 119 2019-08-14 00:21 41 ********************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC