smartctl 6.5 2016-05-07 r4318 [x86_64-linux-4.13.10-1-default] (SUSE RPM) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WDC WD5000LPLX-00ZNTT0 Firmware Version: 01.01A01 User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Nov 27 19:28:09 2017 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 6720) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 79) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 143 143 021 - 1825 4 Start_Stop_Count -O--CK 100 100 000 - 21 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 12 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 21 192 Power-Off_Retract_Count -O--CK 200 200 000 - 1 193 Load_Cycle_Count -O--CK 200 200 000 - 118 194 Temperature_Celsius -O---K 106 102 000 - 37 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 37 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 12 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 37 Celsius Power Cycle Min/Max Temperature: 35/37 Celsius Lifetime Min/Max Temperature: 22/41 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (112) Index Estimated Time Temperature Celsius 113 2017-11-27 17:21 38 ******************* 114 2017-11-27 17:22 38 ******************* 115 2017-11-27 17:23 37 ****************** ... ..( 6 skipped). .. ****************** 122 2017-11-27 17:30 37 ****************** 123 2017-11-27 17:31 36 ***************** ... ..( 2 skipped). .. ***************** 126 2017-11-27 17:34 36 ***************** 127 2017-11-27 17:35 35 **************** ... ..( 3 skipped). .. **************** 3 2017-11-27 17:39 35 **************** 4 2017-11-27 17:40 36 ***************** ... ..( 2 skipped). .. ***************** 7 2017-11-27 17:43 36 ***************** 8 2017-11-27 17:44 37 ****************** ... ..( 3 skipped). .. ****************** 12 2017-11-27 17:48 37 ****************** 13 2017-11-27 17:49 36 ***************** ... ..( 2 skipped). .. ***************** 16 2017-11-27 17:52 36 ***************** 17 2017-11-27 17:53 35 **************** ... ..( 25 skipped). .. **************** 43 2017-11-27 18:19 35 **************** 44 2017-11-27 18:20 ? - 45 2017-11-27 18:21 22 *** 46 2017-11-27 18:22 22 *** 47 2017-11-27 18:23 24 ***** 48 2017-11-27 18:24 24 ***** 49 2017-11-27 18:25 25 ****** 50 2017-11-27 18:26 26 ******* 51 2017-11-27 18:27 26 ******* 52 2017-11-27 18:28 27 ******** 53 2017-11-27 18:29 28 ********* 54 2017-11-27 18:30 29 ********** 55 2017-11-27 18:31 29 ********** 56 2017-11-27 18:32 ? - 57 2017-11-27 18:33 30 *********** 58 2017-11-27 18:34 30 *********** 59 2017-11-27 18:35 31 ************ 60 2017-11-27 18:36 31 ************ 61 2017-11-27 18:37 31 ************ 62 2017-11-27 18:38 32 ************* ... ..( 2 skipped). .. ************* 65 2017-11-27 18:41 32 ************* 66 2017-11-27 18:42 33 ************** 67 2017-11-27 18:43 34 *************** ... ..( 2 skipped). .. *************** 70 2017-11-27 18:46 34 *************** 71 2017-11-27 18:47 35 **************** ... ..( 2 skipped). .. **************** 74 2017-11-27 18:50 35 **************** 75 2017-11-27 18:51 36 ***************** ... ..( 9 skipped). .. ***************** 85 2017-11-27 19:01 36 ***************** 86 2017-11-27 19:02 37 ****************** ... ..( 12 skipped). .. ****************** 99 2017-11-27 19:15 37 ****************** 100 2017-11-27 19:16 ? - 101 2017-11-27 19:17 37 ****************** 102 2017-11-27 19:18 36 ***************** 103 2017-11-27 19:19 36 ***************** 104 2017-11-27 19:20 35 **************** ... ..( 5 skipped). .. **************** 110 2017-11-27 19:26 35 **************** 111 2017-11-27 19:27 36 ***************** 112 2017-11-27 19:28 37 ****************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 766 Vendor specific