[Smartmontools-database] Seagate ST9500325AS (firmware 0001SDM1)
astian
astian at memeware.net
Sun May 10 09:48:48 CEST 2026
As explained here [0] this disk is technically already in drivedb but
the relevant pattern is too broad and shouldn't match this firmware.
0: https://listi.jpberlin.de/pipermail/smartmontools-support/2026-April/001171.html
As explained later in the same thread, I took this log dump *after*
applying my own drivedb override which *disables* the incorrect
"xerrorlba" fixup, so while the log says "In smartctl database",
smartctl's behaviour is ~ as if it wasn't.
Cheers.
-------------- next part --------------
smartctl 7.5 2025-04-30 r5714 [x86_64-linux-6.12.74+deb13+1-amd64] (local build)
Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Momentus 5400.6
Device Model: ST9500325AS
Firmware Version: 0001SDM1
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 5400 rpm
Device is: In smartctl database
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Tue Apr 14 19:47:49 2026 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 254 (maximum performance)
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, frozen [SEC2]
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 135) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103b) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-- 111 097 006 - 32788399
3 Spin_Up_Time PO---- 098 098 000 - 0
4 Start_Stop_Count -O--CK 096 096 020 - 4564
5 Reallocated_Sector_Ct PO--CK 054 054 036 - 906
7 Seek_Error_Rate POSR-- 079 060 030 - 26355198920
9 Power_On_Hours -O--CK 058 031 000 - 36914
10 Spin_Retry_Count PO--C- 100 100 097 - 0
12 Power_Cycle_Count -O--CK 099 099 020 - 1030
184 End-to-End_Error -O--CK 100 100 099 - 0
187 Reported_Uncorrect -O--CK 001 001 000 - 2231
188 Command_Timeout -O--CK 100 089 000 - 64425492528
189 High_Fly_Writes -O-RCK 100 100 000 - 0
190 Airflow_Temperature_Cel -O---K 068 057 045 - 32 (Min/Max 21/35)
191 G-Sense_Error_Rate -O--CK 100 100 000 - 87
192 Power-Off_Retract_Count -O--CK 100 100 000 - 17
193 Load_Cycle_Count -O--CK 001 001 000 - 246016
194 Temperature_Celsius -O---K 032 043 000 - 32 (0 10 0 0 0)
195 Hardware_ECC_Recovered -O-RC- 052 047 000 - 32788399
197 Current_Pending_Sector -O--C- 100 100 000 - 10
198 Offline_Uncorrectable ----C- 100 100 000 - 10
199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 10
254 Free_Fall_Sensor -O--CK 100 100 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 GPL,SL R/O 1 Summary SMART error log
0x02 GPL,SL R/O 5 Comprehensive SMART error log
0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log
0x06 GPL,SL R/O 1 SMART self-test log
0x07 GPL,SL R/O 1 Extended self-test log
0x09 GPL,SL R/W 1 Selective self-test log
0x10 GPL,SL R/O 1 NCQ Command Error log
0x11 GPL,SL R/O 1 SATA Phy Event Counters log
0x21 GPL,SL R/O 1 Write stream error log
0x22 GPL,SL R/O 1 Read stream error log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa1 GPL,SL VS 20 Device vendor specific log
0xa2 GPL VS 2248 Device vendor specific log
0xa8 GPL,SL VS 65 Device vendor specific log
0xa9 GPL,SL VS 1 Device vendor specific log
0xb0 GPL VS 2864 Device vendor specific log
0xbe-0xbf GPL VS 65535 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
Device Error Count: 2107 (device log contains only the most recent 20 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 2107 [16] occurred at disk power-on lifetime: 33714 hours (1404 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 23 61 35 44 00 00 Error: UNC at LBA = 0x23613544 = 593573188
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 01 00 00 00 23 61 35 04 40 00 4d+19:33:09.598 READ FPDMA QUEUED
60 00 00 00 20 00 00 23 61 34 e4 40 00 4d+19:33:09.285 READ FPDMA QUEUED
60 00 00 01 00 00 00 23 60 6e cd 40 00 4d+19:33:09.155 READ FPDMA QUEUED
60 00 00 00 68 00 00 23 60 6e 65 40 00 4d+19:33:09.143 READ FPDMA QUEUED
60 00 00 01 00 00 00 23 61 a8 b2 40 00 4d+19:33:09.072 READ FPDMA QUEUED
Error 2106 [15] occurred at disk power-on lifetime: 20062 hours (835 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 30 9a 25 90 00 00 Error: UNC at LBA = 0x309a2590 = 815408528
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
42 d0 0b 08 00 00 00 30 9a 25 8c e0 00 02:11:48.017 READ VERIFY SECTOR(S) EXT
42 d0 0b 08 00 00 00 30 9a 1e 42 e0 00 02:11:45.767 READ VERIFY SECTOR(S) EXT
42 d0 0b 08 00 00 00 30 9a 16 42 e0 00 02:11:45.642 READ VERIFY SECTOR(S) EXT
42 d0 0b 08 00 00 00 30 9a 0e 42 e0 00 02:11:45.569 READ VERIFY SECTOR(S) EXT
42 d0 0b 08 00 00 00 30 9a 06 42 e0 00 02:11:45.501 READ VERIFY SECTOR(S) EXT
Error 2105 [14] occurred at disk power-on lifetime: 20062 hours (835 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 30 9a 25 8b 00 00 Error: UNC at LBA = 0x309a258b = 815408523
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
42 d0 0b 08 00 00 00 30 9a 1e 42 e0 00 02:11:45.767 READ VERIFY SECTOR(S) EXT
42 d0 0b 08 00 00 00 30 9a 16 42 e0 00 02:11:45.642 READ VERIFY SECTOR(S) EXT
42 d0 0b 08 00 00 00 30 9a 0e 42 e0 00 02:11:45.569 READ VERIFY SECTOR(S) EXT
42 d0 0b 08 00 00 00 30 9a 06 42 e0 00 02:11:45.501 READ VERIFY SECTOR(S) EXT
42 00 00 08 00 00 00 30 99 fe 42 40 00 02:11:45.443 READ VERIFY SECTOR(S) EXT
Error 2104 [13] occurred at disk power-on lifetime: 20062 hours (835 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 30 8a 41 4d 00 00 Error: UNC at LBA = 0x308a414d = 814367053
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
42 d0 0b 08 00 00 00 30 8a 3b 80 e0 00 02:11:31.869 READ VERIFY SECTOR(S) EXT
42 d0 0b 08 00 00 00 30 8a 33 80 e0 00 02:11:31.783 READ VERIFY SECTOR(S) EXT
42 d0 0b 08 00 00 00 30 8a 2b 80 e0 00 02:11:31.610 READ VERIFY SECTOR(S) EXT
42 d0 0b 08 00 00 00 30 8a 23 80 e0 00 02:11:31.487 READ VERIFY SECTOR(S) EXT
42 d0 0b 08 00 00 00 30 8a 1b 80 e0 00 02:11:31.471 READ VERIFY SECTOR(S) EXT
Error 2103 [12] occurred at disk power-on lifetime: 20061 hours (835 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 30 71 b2 3a 00 00 Error: UNC at LBA = 0x3071b23a = 812757562
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
42 d0 0b 08 00 00 00 30 71 b2 39 e0 00 01:07:56.993 READ VERIFY SECTOR(S) EXT
42 d0 0b 08 00 00 00 30 71 b2 35 e0 00 01:07:54.722 READ VERIFY SECTOR(S) EXT
42 00 00 08 00 00 00 30 71 b0 00 40 00 01:07:52.634 READ VERIFY SECTOR(S) EXT
42 d0 0b 08 00 00 00 30 71 a8 00 e0 00 01:07:52.875 READ VERIFY SECTOR(S) EXT
42 00 00 08 00 00 00 30 71 a0 00 40 00 01:07:52.609 READ VERIFY SECTOR(S) EXT
Error 2102 [11] occurred at disk power-on lifetime: 20061 hours (835 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 30 71 b2 38 00 00 Error: UNC at LBA = 0x3071b238 = 812757560
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
42 d0 0b 08 00 00 00 30 71 b2 35 e0 00 01:07:54.722 READ VERIFY SECTOR(S) EXT
42 00 00 08 00 00 00 30 71 b0 00 40 00 01:07:52.634 READ VERIFY SECTOR(S) EXT
42 d0 0b 08 00 00 00 30 71 a8 00 e0 00 01:07:52.875 READ VERIFY SECTOR(S) EXT
42 00 00 08 00 00 00 30 71 a0 00 40 00 01:07:52.609 READ VERIFY SECTOR(S) EXT
42 d0 0b 08 00 00 00 30 69 d8 00 e0 00 01:07:46.975 READ VERIFY SECTOR(S) EXT
Error 2101 [10] occurred at disk power-on lifetime: 20061 hours (835 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 30 71 b2 34 00 00 Error: UNC at LBA = 0x3071b234 = 812757556
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
42 00 00 08 00 00 00 30 71 b0 00 40 00 01:07:52.634 READ VERIFY SECTOR(S) EXT
42 d0 0b 08 00 00 00 30 71 a8 00 e0 00 01:07:52.875 READ VERIFY SECTOR(S) EXT
42 00 00 08 00 00 00 30 71 a0 00 40 00 01:07:52.609 READ VERIFY SECTOR(S) EXT
42 d0 0b 08 00 00 00 30 69 d8 00 e0 00 01:07:46.975 READ VERIFY SECTOR(S) EXT
42 00 00 08 00 00 00 30 59 e8 00 40 00 01:07:36.010 READ VERIFY SECTOR(S) EXT
Error 2100 [9] occurred at disk power-on lifetime: 14973 hours (623 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 30 54 a3 af 00 00 Error: UNC at LBA = 0x3054a3af = 810853295
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
24 00 00 00 01 00 00 30 54 a3 af e0 00 13:41:37.277 READ SECTOR(S) EXT
e5 00 00 00 00 00 00 00 00 00 00 00 00 13:41:34.549 CHECK POWER MODE
e5 00 00 00 00 00 00 00 00 00 00 00 00 13:41:29.547 CHECK POWER MODE
e5 00 00 00 00 00 00 00 00 00 00 00 00 13:41:24.545 CHECK POWER MODE
e5 00 00 00 00 00 00 00 00 00 00 00 00 13:41:19.543 CHECK POWER MODE
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Selective offline Completed without error 00% 36712 -
# 2 Selective offline Completed without error 00% 36684 -
# 3 Selective offline Completed: read failure 90% 36684 856073602
# 4 Selective offline Completed without error 00% 36684 -
# 5 Selective offline Completed without error 00% 36684 -
# 6 Selective offline Completed without error 00% 36684 -
# 7 Selective offline Completed: read failure 90% 36684 815408528
# 8 Selective offline Completed: read failure 90% 36684 815408523
# 9 Selective offline Completed: read failure 90% 36684 814367053
#10 Selective offline Completed without error 00% 36684 -
#11 Selective offline Completed: read failure 90% 36684 812757562
#12 Selective offline Completed: read failure 90% 36684 812757560
#13 Selective offline Completed: read failure 90% 36684 812757556
#14 Selective offline Completed without error 00% 36684 -
#15 Short offline Completed without error 00% 36673 -
#16 Conveyance offline Completed without error 00% 36673 -
#17 Conveyance offline Completed: read failure 90% 36668 800864239
#18 Short offline Completed: read failure 90% 36665 800864239
#19 Selective offline Completed without error 00% 31004 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 800000000 900000000 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 522 (0x020a)
Device State: Active (0)
Current Temperature: 32 Celsius
Power Cycle Min/Max Temperature: 21/35 Celsius
Lifetime Min/Max Temperature: 10/43 Celsius
Under/Over Temperature Limit Count: 0/9
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/ 0 Celsius
Min/Max Temperature Limit: 0/ 0 Celsius
Temperature History Size (Index): 128 (92)
Index Estimated Time Temperature Celsius
93 2026-04-14 17:40 33 **************
... ..( 42 skipped). .. **************
8 2026-04-14 18:23 33 **************
9 2026-04-14 18:24 34 ***************
... ..( 52 skipped). .. ***************
62 2026-04-14 19:17 34 ***************
63 2026-04-14 19:18 33 **************
64 2026-04-14 19:19 32 *************
65 2026-04-14 19:20 31 ************
66 2026-04-14 19:21 30 ***********
67 2026-04-14 19:22 30 ***********
68 2026-04-14 19:23 31 ************
... ..( 4 skipped). .. ************
73 2026-04-14 19:28 31 ************
74 2026-04-14 19:29 32 *************
... ..( 8 skipped). .. *************
83 2026-04-14 19:38 32 *************
84 2026-04-14 19:39 33 **************
... ..( 6 skipped). .. **************
91 2026-04-14 19:46 33 **************
92 2026-04-14 19:47 32 *************
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
Device Statistics (GP/SMART Log 0x04) not supported
Pending Defects log (GP Log 0x0c) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x000a 2 4 Device-to-host register FISes sent due to a COMRESET
0x0001 2 0 Command failed due to ICRC error
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
More information about the Smartmontools-database
mailing list