[Smartmontools-database] Old one missing from drivedb: SanDisk SD8SMAT-032G-1006
Luigi Baldoni
aloisio at gmx.com
Wed Mar 19 18:02:56 CET 2025
smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.0-32-amd64] (local build)
Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: SanDisk SD8SMAT-032G-1006
Firmware Version: Z2311006
User Capacity: 32,017,047,552 bytes [32.0 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: Solid State Device
Form Factor: M.2
TRIM Command: Available, deterministic, zeroed
Device is: Not in smartctl database 7.3/5671
ATA Version is: ACS-2 T13/2015-D revision 3
SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Wed Mar 19 17:54:02 2025 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 254 (maximum performance)
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Unavailable
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x02) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x11) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 10) minutes.
SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 100 100 050 - 0
5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0
9 Power_On_Hours -O--CK 100 100 000 - 1345
12 Power_Cycle_Count -O--CK 100 100 000 - 317
171 Unknown_Attribute -O---K 100 100 000 - 0
172 Unknown_Attribute -O--CK 100 100 000 - 0
173 Unknown_Attribute PO--CK 100 100 005 - 324
174 Unknown_Attribute -O--CK 100 100 000 - 169
187 Reported_Uncorrect -O--CK 100 100 000 - 0
188 Command_Timeout -O--CK 100 100 000 - 0
194 Temperature_Celsius -O---K 060 000 000 - 40 (Min/Max 0/100)
196 Reallocated_Event_Count -O--CK 100 100 000 - 0
199 UDMA_CRC_Error_Count -O--CK 100 100 000 - 3
230 Unknown_SSD_Attribute -O--CK 100 100 000 - 3156
244 Unknown_Attribute -O--CK 000 100 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 1 Comprehensive SMART error log
0x03 GPL R/O 1 Ext. Comprehensive SMART error log
0x04 GPL,SL R/O 8 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
Device Error Count: 3
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 3 [2] occurred at disk power-on lifetime: 65535 hours (2730 days + 15 hours)
When the command that caused the error occurred, the device was in a vendor specific state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
ff -- ff ff ff ff ff ff ff ff ff ff ff
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC]
ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC]
ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC]
ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC]
ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC]
Error 2 [1] occurred at disk power-on lifetime: 65535 hours (2730 days + 15 hours)
When the command that caused the error occurred, the device was in a vendor specific state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
ff -- ff ff ff ff ff ff ff ff ff ff ff
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC]
ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC]
ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC]
ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC]
ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC]
Error 1 [0] occurred at disk power-on lifetime: 65535 hours (2730 days + 15 hours)
When the command that caused the error occurred, the device was in a vendor specific state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
ff -- ff ff ff ff ff ff ff ff ff ff ff
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC]
ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC]
ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC]
ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC]
ff ff ff ff ff ff ff ff ff ff ff ff ff 49d+17:02:47.295 [VENDOR SPECIFIC]
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 1345 -
# 2 Extended offline Completed without error 00% 1345 -
# 3 Short offline Aborted by host 00% 1345 -
# 4 Short offline Completed without error 00% 1345 -
# 5 Short offline Completed without error 00% 0 -
Selective Self-tests/Logging not supported
SCT Commands not supported
Device Statistics (GP Log 0x04)
Page Offset Size Value Flags Description
0x01 ===== = = === == General Statistics (rev 1) ==
0x01 0x008 4 317 --- Lifetime Power-On Resets
0x01 0x010 4 1345 --- Power-on Hours
0x01 0x018 6 2758876390 --- Logical Sectors Written
0x01 0x020 6 218027227 --- Number of Write Commands
0x01 0x028 6 157357012 --- Logical Sectors Read
0x01 0x030 6 270300286 --- Number of Read Commands
0x04 ===== = = === == General Errors Statistics (rev 1) ==
0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors
0x04 0x010 4 169 --- Resets Between Cmd Acceptance and Completion
0x05 ===== = = === == Temperature Statistics (rev 1) ==
0x05 0x008 1 40 --- Current Temperature
0x05 0x010 1 72 --- Average Short Term Temperature
0x05 0x018 1 -1 --- Average Long Term Temperature
0x05 0x020 1 60 --- Highest Temperature
0x05 0x028 1 5 --- Lowest Temperature
0x05 0x030 1 -1 --- Highest Average Short Term Temperature
0x05 0x038 1 0 --- Lowest Average Short Term Temperature
0x05 0x040 1 -1 --- Highest Average Long Term Temperature
0x05 0x048 1 0 --- Lowest Average Long Term Temperature
0x05 0x050 4 0 --- Time in Over-Temperature
0x05 0x058 1 100 --- Specified Maximum Operating Temperature
0x05 0x060 4 0 --- Time in Under-Temperature
0x05 0x068 1 0 --- Specified Minimum Operating Temperature
0x06 ===== = = === == Transport Statistics (rev 1) ==
0x06 0x008 4 7197 --- Number of Hardware Resets
0x06 0x018 4 3 --- Number of Interface CRC Errors
0x07 ===== = = === == Solid State Device Statistics (rev 1) ==
0x07 0x008 1 10 --- Percentage Used Endurance Indicator
|||_ C monitored condition met
||__ D supports DSN
|___ N normalized value
Pending Defects log (GP Log 0x0c) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 4 0 Command failed due to ICRC error
0x0002 4 0 R_ERR response for data FIS
0x0005 4 12 R_ERR response for non-data FIS
0x000a 4 58 Device-to-host register FISes sent due to a COMRESET
More information about the Smartmontools-database
mailing list