[Smartmontools-database] WD My Passport 2627 (4008)
Roman Stingler
r.stingler at gmx.at
Tue Mar 3 21:27:09 CET 2020
Please add this to the database.
Thx
-------------- next part --------------
smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.5.7-arch1-1] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: WDC WD50NDZW-11MR8S1
Serial Number: WD-WXC1E7965VCA
LU WWN Device Id: 5 0014ee 2bc79a546
Firmware Version: 02.01A02
User Capacity: 5,000,947,523,584 bytes [5.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-3 (minor revision not indicated)
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Tue Mar 3 21:24:55 2020 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 128 (minimum power consumption without standby)
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 121) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: ( 1200) seconds.
Offline data collection
capabilities: (0x1b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 352) minutes.
SCT capabilities: (0x30b5) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 200 200 051 - 20
3 Spin_Up_Time POS--K 253 253 021 - 4250
4 Start_Stop_Count -O--CK 100 100 000 - 388
5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
7 Seek_Error_Rate -OSR-K 200 200 000 - 0
9 Power_On_Hours -O--CK 099 099 000 - 813
10 Spin_Retry_Count -O--CK 100 100 000 - 0
11 Calibration_Retry_Count -O--CK 100 253 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 33
192 Power-Off_Retract_Count -O--CK 200 200 000 - 16
193 Load_Cycle_Count -O--CK 200 200 000 - 909
194 Temperature_Celsius -O---K 120 101 000 - 32
196 Reallocated_Event_Count -O--CK 200 200 000 - 0
197 Current_Pending_Sector -O--CK 200 200 000 - 2
198 Offline_Uncorrectable ----CK 100 253 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 8
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 6 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x24 GPL R/O 277 Current Device Internal Status Data log
0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
0xa8-0xb6 GPL,SL VS 1 Device vendor specific log
0xb7 GPL,SL VS 81 Device vendor specific log
0xbd GPL,SL VS 1 Device vendor specific log
0xc0 GPL,SL VS 1 Device vendor specific log
0xc1 GPL VS 93 Device vendor specific log
0xcf GPL VS 65535 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 16
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 16 [15] occurred at disk power-on lifetime: 812 hours (33 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 01 00 00 19 19 d3 c0 40 00 Error: UNC at LBA = 0x1919d3c0 = 421123008
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
42 00 00 00 01 00 00 19 19 d3 c0 40 00 00:00:34.548 READ VERIFY SECTOR(S) EXT
e7 00 00 00 28 00 00 00 2f d7 c8 00 00 00:00:34.494 FLUSH CACHE
25 00 00 00 28 00 02 46 2f d7 c8 40 00 00:00:30.413 READ DMA EXT
25 00 00 00 38 00 02 46 2f d7 88 40 00 00:00:30.413 READ DMA EXT
25 00 00 00 78 00 02 46 2f d7 08 40 00 00:00:30.413 READ DMA EXT
Error 15 [14] occurred at disk power-on lifetime: 812 hours (33 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 01 00 00 19 19 d3 c8 40 00 Error: UNC at LBA = 0x1919d3c8 = 421123016
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
42 00 00 00 01 00 00 19 19 d3 c8 40 00 00:00:27.444 READ VERIFY SECTOR(S) EXT
e7 00 00 00 28 00 00 00 2f d7 c8 00 00 00:00:27.412 FLUSH CACHE
25 00 00 00 28 00 02 46 2f d7 c8 40 00 00:00:18.390 READ DMA EXT
25 00 00 00 38 00 02 46 2f d7 88 40 00 00:00:18.390 READ DMA EXT
25 00 00 00 78 00 02 46 2f d7 08 40 00 00:00:18.389 READ DMA EXT
Error 14 [13] occurred at disk power-on lifetime: 812 hours (33 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 01 00 00 19 19 d3 c0 40 00 Error: UNC at LBA = 0x1919d3c0 = 421123008
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
42 00 00 00 01 00 00 19 19 d3 c0 40 00 01:19:17.639 READ VERIFY SECTOR(S) EXT
e7 00 00 00 28 00 00 00 2f d7 c8 00 00 01:19:17.639 FLUSH CACHE
25 00 00 00 28 00 02 46 2f d7 c8 40 00 01:19:07.194 READ DMA EXT
25 00 00 00 38 00 02 46 2f d7 88 40 00 01:19:07.194 READ DMA EXT
25 00 00 00 78 00 02 46 2f d7 08 40 00 01:19:07.194 READ DMA EXT
Error 13 [12] occurred at disk power-on lifetime: 812 hours (33 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 01 00 00 19 19 d3 cf 40 00 Error: UNC at LBA = 0x1919d3cf = 421123023
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
42 00 00 00 01 00 00 19 19 d3 cf 40 00 01:19:03.644 READ VERIFY SECTOR(S) EXT
e7 00 00 00 28 00 00 00 2f d7 c8 00 00 01:19:03.644 FLUSH CACHE
25 00 00 00 28 00 02 46 2f d7 c8 40 00 01:18:54.715 READ DMA EXT
25 00 00 00 38 00 02 46 2f d7 88 40 00 01:18:54.715 READ DMA EXT
25 00 00 00 78 00 02 46 2f d7 08 40 00 01:18:54.715 READ DMA EXT
Error 12 [11] occurred at disk power-on lifetime: 812 hours (33 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 01 00 00 19 19 d3 cf 40 00 Error: UNC at LBA = 0x1919d3cf = 421123023
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
42 00 00 00 01 00 00 19 19 d3 cf 40 00 01:18:51.763 READ VERIFY SECTOR(S) EXT
e7 00 00 00 28 00 00 00 2f d7 c8 00 00 01:18:51.762 FLUSH CACHE
25 00 00 00 28 00 02 46 2f d7 c8 40 00 01:18:49.417 READ DMA EXT
25 00 00 00 38 00 02 46 2f d7 88 40 00 01:18:49.417 READ DMA EXT
25 00 00 00 78 00 02 46 2f d7 08 40 00 01:18:49.417 READ DMA EXT
Error 11 [10] occurred at disk power-on lifetime: 812 hours (33 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 01 00 00 19 19 d3 ce 40 00 Error: UNC at LBA = 0x1919d3ce = 421123022
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
42 00 00 00 01 00 00 19 19 d3 ce 40 00 01:18:37.574 READ VERIFY SECTOR(S) EXT
e7 00 00 00 28 00 00 00 2f d7 c8 00 00 01:18:37.573 FLUSH CACHE
25 00 00 00 28 00 02 46 2f d7 c8 40 00 01:18:34.757 READ DMA EXT
25 00 00 00 38 00 02 46 2f d7 88 40 00 01:18:34.757 READ DMA EXT
25 00 00 00 78 00 02 46 2f d7 08 40 00 01:18:34.757 READ DMA EXT
Error 10 [9] occurred at disk power-on lifetime: 812 hours (33 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 01 00 00 19 19 d3 cc 40 00 Error: UNC at LBA = 0x1919d3cc = 421123020
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
42 00 00 00 01 00 00 19 19 d3 cc 40 00 01:18:31.806 READ VERIFY SECTOR(S) EXT
e7 00 00 00 28 00 00 00 2f d7 c8 00 00 01:18:31.805 FLUSH CACHE
25 00 00 00 28 00 02 46 2f d7 c8 40 00 01:18:28.281 READ DMA EXT
25 00 00 00 38 00 02 46 2f d7 88 40 00 01:18:28.280 READ DMA EXT
25 00 00 00 78 00 02 46 2f d7 08 40 00 01:18:28.280 READ DMA EXT
Error 9 [8] occurred at disk power-on lifetime: 812 hours (33 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 01 00 00 19 19 d3 cc 40 00 Error: UNC at LBA = 0x1919d3cc = 421123020
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
42 00 00 00 01 00 00 19 19 d3 cc 40 00 01:18:11.833 READ VERIFY SECTOR(S) EXT
e7 00 00 00 28 00 00 00 2f d7 c8 00 00 01:18:11.832 FLUSH CACHE
25 00 00 00 28 00 02 46 2f d7 c8 40 00 01:18:07.436 READ DMA EXT
25 00 00 00 38 00 02 46 2f d7 88 40 00 01:18:07.435 READ DMA EXT
25 00 00 00 78 00 02 46 2f d7 08 40 00 01:18:07.435 READ DMA EXT
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed: read failure 90% 812 421123008
# 2 Extended offline Completed: read failure 90% 812 421123016
# 3 Extended offline Completed: read failure 90% 812 421123008
# 4 Extended offline Completed: read failure 90% 811 421123008
# 5 Extended offline Completed: read failure 90% 811 421123008
# 6 Extended offline Completed: read failure 90% 811 421123008
# 7 Short offline Completed without error 00% 795 -
# 8 Short offline Completed without error 00% 771 -
# 9 Short offline Completed without error 00% 747 -
#10 Extended offline Completed: read failure 90% 724 421123008
#11 Short offline Completed without error 00% 723 -
#12 Short offline Completed without error 00% 700 -
#13 Short offline Completed without error 00% 676 -
#14 Short offline Completed without error 00% 652 -
#15 Short offline Completed without error 00% 628 -
#16 Short offline Completed without error 00% 604 -
#17 Short offline Completed without error 00% 580 -
#18 Extended offline Completed: read failure 90% 566 421123008
Selective Self-tests/Logging not supported
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
Device State: Active (0)
Current Temperature: 32 Celsius
Power Cycle Min/Max Temperature: 32/37 Celsius
Lifetime Min/Max Temperature: 18/50 Celsius
Specified Max Operating Temperature: 43 Celsius
Under/Over Temperature Limit Count: 0/0
Vendor specific:
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 128 (4)
Index Estimated Time Temperature Celsius
5 2020-03-03 19:17 32 *************
6 2020-03-03 19:18 32 *************
7 2020-03-03 19:19 ? -
8 2020-03-03 19:20 30 ***********
9 2020-03-03 19:21 ? -
10 2020-03-03 19:22 28 *********
11 2020-03-03 19:23 ? -
12 2020-03-03 19:24 21 **
13 2020-03-03 19:25 22 ***
14 2020-03-03 19:26 22 ***
15 2020-03-03 19:27 23 ****
16 2020-03-03 19:28 24 *****
... ..( 2 skipped). .. *****
19 2020-03-03 19:31 24 *****
20 2020-03-03 19:32 25 ******
... ..( 2 skipped). .. ******
23 2020-03-03 19:35 25 ******
24 2020-03-03 19:36 26 *******
... ..( 2 skipped). .. *******
27 2020-03-03 19:39 26 *******
28 2020-03-03 19:40 27 ********
... ..( 3 skipped). .. ********
32 2020-03-03 19:44 27 ********
33 2020-03-03 19:45 28 *********
... ..( 7 skipped). .. *********
41 2020-03-03 19:53 28 *********
42 2020-03-03 19:54 29 **********
... ..( 11 skipped). .. **********
54 2020-03-03 20:06 29 **********
55 2020-03-03 20:07 30 ***********
... ..( 15 skipped). .. ***********
71 2020-03-03 20:23 30 ***********
72 2020-03-03 20:24 31 ************
... ..( 15 skipped). .. ************
88 2020-03-03 20:40 31 ************
89 2020-03-03 20:41 32 *************
... ..( 5 skipped). .. *************
95 2020-03-03 20:47 32 *************
96 2020-03-03 20:48 33 **************
97 2020-03-03 20:49 34 ***************
98 2020-03-03 20:50 35 ****************
99 2020-03-03 20:51 35 ****************
100 2020-03-03 20:52 36 *****************
101 2020-03-03 20:53 37 ******************
102 2020-03-03 20:54 37 ******************
103 2020-03-03 20:55 ? -
104 2020-03-03 20:56 37 ******************
105 2020-03-03 20:57 37 ******************
106 2020-03-03 20:58 37 ******************
107 2020-03-03 20:59 36 *****************
108 2020-03-03 21:00 36 *****************
109 2020-03-03 21:01 35 ****************
... ..( 3 skipped). .. ****************
113 2020-03-03 21:05 35 ****************
114 2020-03-03 21:06 34 ***************
... ..( 6 skipped). .. ***************
121 2020-03-03 21:13 34 ***************
122 2020-03-03 21:14 33 **************
... ..( 6 skipped). .. **************
1 2020-03-03 21:21 33 **************
2 2020-03-03 21:22 32 *************
3 2020-03-03 21:23 32 *************
4 2020-03-03 21:24 32 *************
SCT Error Recovery Control command not supported
Device Statistics (GP/SMART Log 0x04) not supported
Pending Defects log (GP Log 0x0c) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 1 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x8000 4 1726 Vendor specific
More information about the Smartmontools-database
mailing list