[Smartmontools-database] Toshiba NAS N300 8TB
Matthew Carr
matt.carr at dubious-reality.com
Fri Jun 12 16:26:13 CEST 2020
SMART report info from a slightly sick N300
# Toshiba NAS N300 8TB
smartctl 7.0 2018-12-30 r4883 [x86_64-linux-5.6.15-gentoo-x86_64] (local
build)
Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: TOSHIBA HDWN180
Serial Number: 99MAK15FFAVG
LU WWN Device Id: 5 000039 98bb81c95
Firmware Version: GX2M
User Capacity: 8,001,563,222,016 bytes [8.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-3 T13/2161-D revision 5
SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Fri Jun 12 15:11:29 2020 BST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 128 (minimum power consumption without standby)
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Disabled
ATA Security is: Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x85) Offline data collection activity
was aborted by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 745) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 0
2 Throughput_Performance P-S--- 100 100 050 - 0
3 Spin_Up_Time POS--K 100 100 001 - 10602
4 Start_Stop_Count -O--CK 100 100 000 - 44
5 Reallocated_Sector_Ct PO--CK 100 100 050 - 1304
7 Seek_Error_Rate PO-R-- 100 051 050 - 0
8 Seek_Time_Performance P-S--- 100 100 050 - 0
9 Power_On_Hours -O--CK 087 087 000 - 5213
10 Spin_Retry_Count PO--CK 100 100 030 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 44
191 G-Sense_Error_Rate -O--CK 100 100 000 - 0
192 Power-Off_Retract_Count -O--CK 100 100 000 - 28
193 Load_Cycle_Count -O--CK 084 084 000 - 164527
194 Temperature_Celsius -O---K 100 100 000 - 38 (Min/Max
15/49)
196 Reallocated_Event_Count -O--CK 100 100 000 - 139
197 Current_Pending_Sector -O--CK 100 100 000 - 0
198 Offline_Uncorrectable ----CK 100 100 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 253 000 - 0
220 Disk_Shift -O---- 100 100 000 - 0
222 Loaded_Hours -O--CK 092 092 000 - 3475
223 Load_Retry_Count -O--CK 100 100 000 - 0
224 Load_Friction -O---K 100 100 000 - 0
226 Load-in_Time -OS--K 100 100 000 - 634
240 Head_Flying_Hours P----- 100 100 001 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 51 Comprehensive SMART error log
0x03 GPL R/O 64 Ext. Comprehensive SMART error log
0x04 GPL,SL R/O 8 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x08 GPL R/O 2 Power Conditions log
0x09 SL R/W 1 Selective self-test log
0x0a GPL R/W 2 Device Statistics Notification
0x0c GPL R/O 2048 Pending Defects log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x24 GPL R/O 16384 Current Device Internal Status Data log
0x25 GPL R/O 16384 Saved Device Internal Status Data log
0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa7 GPL VS 8 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (64 sectors)
Device Error Count: 3
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 3 [2] occurred at disk power-on lifetime: 3499 hours (145 days + 19
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 31 00 00 00 00 00 00 84 02 01 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time
Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- ---------------
--------------------
ec 00 00 00 00 00 00 00 00 00 00 00 00 10:22:43.713 IDENTIFY DEVICE
aa aa aa aa aa aa aa aa aa aa aa aa ff 10:22:43.680 [RESERVED]
60 00 80 00 f8 00 00 03 bc d0 80 40 00 10:22:04.345 READ FPDMA QUEUED
60 00 80 00 f8 00 00 03 c8 c8 80 40 00 10:22:04.336 READ FPDMA QUEUED
60 00 80 00 f0 00 00 03 6d 38 80 40 00 10:22:04.335 READ FPDMA QUEUED
Error 2 [1] occurred at disk power-on lifetime: 3489 hours (145 days + 9
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 31 00 00 00 00 00 20 84 02 01 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time
Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- ---------------
--------------------
ec 00 00 00 00 00 00 00 00 00 00 00 00 00:09:42.567 IDENTIFY DEVICE
ec 00 00 00 00 00 00 00 00 00 00 00 00 00:09:42.567 IDENTIFY DEVICE
ec 00 00 00 00 00 00 00 00 00 00 00 00 00:09:27.868 IDENTIFY DEVICE
aa aa aa aa aa aa aa aa aa aa aa aa ff 00:09:27.245 [RESERVED]
60 00 80 00 f8 00 00 00 0e 76 00 40 00 00:08:08.829 READ FPDMA QUEUED
Error 1 [0] occurred at disk power-on lifetime: 3134 hours (130 days + 14
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 31 00 00 00 00 00 b7 41 34 03 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time
Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- ---------------
--------------------
ec 00 00 00 00 00 00 00 00 00 00 00 00 00:10:40.261 IDENTIFY DEVICE
aa aa aa aa aa aa aa aa aa aa aa aa ff 00:10:39.582 [RESERVED]
60 00 80 00 d0 00 02 31 c2 84 80 40 00 00:08:13.186 READ FPDMA QUEUED
60 00 48 00 c8 00 00 4e fd 67 00 40 00 00:08:11.108 READ FPDMA QUEUED
60 00 20 00 c0 00 01 e4 c6 4b a0 40 00 00:08:10.456 READ FPDMA QUEUED
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Short offline Completed without error 00% 5211
-
# 2 Extended offline Completed without error 00% 3910
-
# 3 Short offline Completed without error 00% 3844
-
# 4 Short offline Completed without error 00% 3489
-
# 5 Extended offline Completed without error 00% 1049
-
# 6 Extended offline Interrupted (host reset) 90% 685
-
# 7 Extended offline Completed without error 00% 165
-
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 1 (0x0001)
Device State: Active (0)
Current Temperature: 38 Celsius
Power Cycle Min/Max Temperature: 29/49 Celsius
Lifetime Min/Max Temperature: 15/49 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 5/55 Celsius
Min/Max Temperature Limit: 5/55 Celsius
Temperature History Size (Index): 478 (441)
Index Estimated Time Temperature Celsius
442 2020-06-12 07:14 35 ****************
443 2020-06-12 07:15 36 *****************
444 2020-06-12 07:16 35 ****************
... ..( 3 skipped). .. ****************
448 2020-06-12 07:20 35 ****************
449 2020-06-12 07:21 36 *****************
... ..( 5 skipped). .. *****************
455 2020-06-12 07:27 36 *****************
456 2020-06-12 07:28 35 ****************
... ..( 3 skipped). .. ****************
460 2020-06-12 07:32 35 ****************
461 2020-06-12 07:33 36 *****************
462 2020-06-12 07:34 36 *****************
463 2020-06-12 07:35 35 ****************
464 2020-06-12 07:36 36 *****************
... ..( 2 skipped). .. *****************
467 2020-06-12 07:39 36 *****************
468 2020-06-12 07:40 35 ****************
469 2020-06-12 07:41 36 *****************
470 2020-06-12 07:42 36 *****************
471 2020-06-12 07:43 35 ****************
472 2020-06-12 07:44 35 ****************
473 2020-06-12 07:45 36 *****************
... ..( 3 skipped). .. *****************
477 2020-06-12 07:49 36 *****************
0 2020-06-12 07:50 35 ****************
1 2020-06-12 07:51 36 *****************
2 2020-06-12 07:52 35 ****************
3 2020-06-12 07:53 36 *****************
4 2020-06-12 07:54 36 *****************
5 2020-06-12 07:55 36 *****************
6 2020-06-12 07:56 35 ****************
7 2020-06-12 07:57 36 *****************
... ..( 23 skipped). .. *****************
31 2020-06-12 08:21 36 *****************
32 2020-06-12 08:22 35 ****************
33 2020-06-12 08:23 36 *****************
34 2020-06-12 08:24 36 *****************
35 2020-06-12 08:25 35 ****************
36 2020-06-12 08:26 36 *****************
... ..(236 skipped). .. *****************
273 2020-06-12 12:23 36 *****************
274 2020-06-12 12:24 37 ******************
... ..( 47 skipped). .. ******************
322 2020-06-12 13:12 37 ******************
323 2020-06-12 13:13 38 *******************
324 2020-06-12 13:14 37 ******************
325 2020-06-12 13:15 38 *******************
... ..(100 skipped). .. *******************
426 2020-06-12 14:56 38 *******************
427 2020-06-12 14:57 37 ******************
428 2020-06-12 14:58 38 *******************
429 2020-06-12 14:59 37 ******************
... ..( 9 skipped). .. ******************
439 2020-06-12 15:09 37 ******************
440 2020-06-12 15:10 38 *******************
441 2020-06-12 15:11 38 *******************
SCT Error Recovery Control:
Read: 70 (7.0 seconds)
Write: 70 (7.0 seconds)
Device Statistics (GP Log 0x04)
Page Offset Size Value Flags Description
0x01 ===== = = === == General Statistics (rev 1) ==
0x01 0x008 4 44 --- Lifetime Power-On Resets
0x01 0x010 4 5213 --- Power-on Hours
0x01 0x018 6 159857571348 --- Logical Sectors Written
0x01 0x020 6 657208405 --- Number of Write Commands
0x01 0x028 6 473115555608 --- Logical Sectors Read
0x01 0x030 6 3415756557 --- Number of Read Commands
0x01 0x038 6 18768131033 --- Date and Time TimeStamp
0x02 ===== = = === == Free-Fall Statistics (rev 1) ==
0x02 0x010 4 0 --- Overlimit Shock Events
0x03 ===== = = === == Rotating Media Statistics (rev 1) ==
0x03 0x008 4 5213 --- Spindle Motor Power-on Hours
0x03 0x010 4 3475 --- Head Flying Hours
0x03 0x018 4 164527 --- Head Load Events
0x03 0x020 4 1304 -D- Number of Reallocated Logical Sectors
0x03 0x028 4 23 --- Read Recovery Attempts
0x03 0x030 4 0 --- Number of Mechanical Start Failures
0x03 0x038 4 0 --- Number of Realloc. Candidate Logical
Sectors
0x03 0x040 4 28 --- Number of High Priority Unload Events
0x04 ===== = = === == General Errors Statistics (rev 1) ==
0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors
0x04 0x010 4 10 --- Resets Between Cmd Acceptance and
Completion
0x05 ===== = = === == Temperature Statistics (rev 1) ==
0x05 0x008 1 38 --- Current Temperature
0x05 0x010 1 36 N-- Average Short Term Temperature
0x05 0x018 1 40 N-- Average Long Term Temperature
0x05 0x020 1 49 --- Highest Temperature
0x05 0x028 1 15 --- Lowest Temperature
0x05 0x030 1 46 N-- Highest Average Short Term Temperature
0x05 0x038 1 22 N-- Lowest Average Short Term Temperature
0x05 0x040 1 42 N-- Highest Average Long Term Temperature
0x05 0x048 1 25 N-- Lowest Average Long Term Temperature
0x05 0x050 4 0 --- Time in Over-Temperature
0x05 0x058 1 55 --- Specified Maximum Operating Temperature
0x05 0x060 4 0 --- Time in Under-Temperature
0x05 0x068 1 5 --- Specified Minimum Operating Temperature
0x06 ===== = = === == Transport Statistics (rev 1) ==
0x06 0x008 4 360 --- Number of Hardware Resets
0x06 0x010 4 64 --- Number of ASR Events
0x06 0x018 4 0 --- Number of Interface CRC Errors
0x07 ===== = = === == Solid State Device Statistics (rev
1) ==
|||_ C monitored condition met
||__ D supports DSN
|___ N normalized value
Pending Defects log (GP Log 0x0c)
No Defects Logged
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 4 0 Command failed due to ICRC error
0x0002 4 0 R_ERR response for data FIS
0x0003 4 0 R_ERR response for device-to-host data FIS
0x0004 4 0 R_ERR response for host-to-device data FIS
0x0005 4 0 R_ERR response for non-data FIS
0x0006 4 0 R_ERR response for device-to-host non-data FIS
0x0007 4 0 R_ERR response for host-to-device non-data FIS
0x0008 4 0 Device-to-host non-data FIS retries
0x0009 4 2 Transition from drive PhyRdy to drive PhyNRdy
0x000a 4 3 Device-to-host register FISes sent due to a COMRESET
0x000b 4 0 CRC errors within host-to-device FIS
0x000d 4 0 Non-CRC errors within host-to-device FIS
0x000f 4 0 R_ERR response for host-to-device data FIS, CRC
0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 4 0 R_ERR response for host-to-device non-data FIS,
non-CRC
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://listi.jpberlin.de/pipermail/smartmontools-database/attachments/20200612/ca463d60/attachment-0001.html>
More information about the Smartmontools-database
mailing list