[Smartmontools-database] Seagate Nytro 1351 SATA SSD
Marco Gruß
mcg at lf.net
Wed Nov 28 14:22:34 CET 2018
Hi,
the SandForce IP Seagate acquired years ago is back,
it seems, as these disks feature "DuraWrite". The SMART
attributes don't look like the old SandForce attributes
though. Attached is the output of smartctl -x of the
1DWPD 240GB model after writing exactly 1 GiB of data
to it.
https://www.seagate.com/ca/en/enterprise-storage/nytro-drives/nytro-sata-ssd/nytro-1000-ssd/
Best,
Marco
-------------- next part --------------
smartctl 6.6 2017-11-05 r4594 [x86_64-linux-4.4.21-1-pve] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: XA240LE10003
Serial Number: HLH01BZG
LU WWN Device Id: 5 000c50 03ea0596e
Firmware Version: SF4400ZG
User Capacity: 240,057,409,536 bytes [240 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: Solid State Device
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-4, ACS-2 T13/2015-D revision 3
SATA Version is: SATA 3.3, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Wed Nov 28 15:03:06 2018 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 254 (maximum performance)
Rd look-ahead is: Disabled
Write cache is: Disabled
DSN feature is: Disabled
ATA Security is: Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x59) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0002) Does not save SMART data before
entering power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 30) minutes.
SCT capabilities: (0x103d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 100 100 090 - 0
5 Reallocated_Sector_Ct -O--CK 100 100 000 - 0
9 Power_On_Hours -O--CK 100 100 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 4
100 Unknown_Attribute -O--CK 100 100 000 - 0
102 Unknown_Attribute -O--CK 100 100 000 - 0
103 Unknown_Attribute -O--CK 100 100 000 - 0
170 Unknown_Attribute -O--CK 100 100 000 - 0
171 Unknown_Attribute -O--CK 100 100 000 - 0
172 Unknown_Attribute -O--CK 100 100 000 - 0
173 Unknown_Attribute -O--CK 100 100 000 - 1
174 Unknown_Attribute -O--CK 100 100 000 - 1
177 Wear_Leveling_Count PO---K 100 100 089 - 0
183 Runtime_Bad_Block -O--CK 099 099 000 - 16777217
187 Reported_Uncorrect -O--CK 100 100 000 - 0
194 Temperature_Celsius -O---K 023 049 000 - 23 (Min/Max 22/49)
195 Hardware_ECC_Recovered -O--CK 100 100 000 - 0
198 Offline_Uncorrectable -O--CK 100 100 000 - 0
199 UDMA_CRC_Error_Count -O--CK 100 100 000 - 0
230 Unknown_SSD_Attribute PO---K 090 100 000 - 90
231 Temperature_Celsius PO--CK 100 100 010 - 6579200
232 Available_Reservd_Space POS--K 100 100 003 - 0
233 Media_Wearout_Indicator -O--CK 100 100 000 - 0
241 Total_LBAs_Written -O--CK 100 100 000 - 1
242 Total_LBAs_Read -O--CK 100 100 000 - 0
243 Unknown_Attribute -OS--K 100 098 003 - 42945378250850
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x02 SL R/O 16 Comprehensive SMART error log
0x03 GPL R/O 20 Ext. Comprehensive SMART error log
0x04 GPL,SL R/O 8 Device Statistics log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x0a GPL R/W 16 Device Statistics Notification
0x0c GPL R/O 1 Pending Defects log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x12 GPL R/O 1 SATA NCQ Non-Data log
0x13 GPL R/O 1 SATA NCQ Send and Receive log
0x24 GPL R/O 65535 Current Device Internal Status Data log
0x25 GPL R/O 65535 Saved Device Internal Status Data log
0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa8 SL VS 255 Device vendor specific log
0xb7 GPL VS 1024 Device vendor specific log
0xd4 GPL,SL VS 6 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
0xf7 SL - 2 Reserved
0xf8 SL - 1 Reserved
0xf9 SL - 4 Reserved
0xfa SL - 7 Reserved
0xfb GPL - 65535 Reserved
SMART Extended Comprehensive Error Log Version: 1 (20 sectors)
Device Error Count: 2
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 2 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 00 00 00 00 00 00 00 00 00 00 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
00 00 00 00 00 00 00 00 00 00 00 00 ff 00:00:28.107 NOP [Abort queued commands]
Error 1 [79] log entry is empty
SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 0 (0x0000)
SCT Support Level: 0
Device State: Active (0)
Current Temperature: 28 Celsius
Power Cycle Min/Max Temperature: 26/28 Celsius
Lifetime Min/Max Temperature: 22/49 Celsius
Under/Over Temperature Limit Count: 0/0
SMART Status: 0xc24f (PASSED)
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: -10/116 Celsius
Min/Max Temperature Limit: -10/120 Celsius
Temperature History Size (Index): 478 (18)
Index Estimated Time Temperature Celsius
19 2018-11-28 07:06 ? -
... ..(458 skipped). .. -
0 2018-11-28 14:45 ? -
1 2018-11-28 14:46 44 *************************
2 2018-11-28 14:47 ? -
... ..( 2 skipped). .. -
5 2018-11-28 14:50 ? -
6 2018-11-28 14:51 23 ****
... ..( 11 skipped). .. ****
18 2018-11-28 15:03 23 ****
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
Device Statistics (GP Log 0x04)
Page Offset Size Value Flags Description
0x01 ===== = = === == General Statistics (rev 1) ==
0x01 0x008 4 4 --- Lifetime Power-On Resets
0x01 0x010 4 0 --- Power-on Hours
0x01 0x018 6 2097152 --- Logical Sectors Written
0x01 0x020 6 1563 --- Number of Write Commands
0x01 0x028 6 1872 --- Logical Sectors Read
0x01 0x030 6 126 --- Number of Read Commands
0x01 0x038 6 932486 --- Date and Time TimeStamp
0x01 0x058 2 65534 --- Resource Availability
0x04 ===== = = === == General Errors Statistics (rev 1) ==
0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors
0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion
0x05 ===== = = === == Temperature Statistics (rev 1) ==
0x05 0x008 1 23 --- Current Temperature
0x05 0x010 1 - --- Average Short Term Temperature
0x05 0x018 1 - --- Average Long Term Temperature
0x05 0x020 1 49 --- Highest Temperature
0x05 0x028 1 22 --- Lowest Temperature
0x05 0x030 1 - --- Highest Average Short Term Temperature
0x05 0x038 1 - --- Lowest Average Short Term Temperature
0x05 0x040 1 - --- Highest Average Long Term Temperature
0x05 0x048 1 - --- Lowest Average Long Term Temperature
0x05 0x050 4 0 --- Time in Over-Temperature
0x05 0x058 1 116 --- Specified Maximum Operating Temperature
0x05 0x060 4 0 --- Time in Under-Temperature
0x05 0x068 1 -10 --- Specified Minimum Operating Temperature
0x06 ===== = = === == Transport Statistics (rev 1) ==
0x06 0x008 4 75 --- Number of Hardware Resets
0x06 0x010 4 26 --- Number of ASR Events
0x06 0x018 4 0 --- Number of Interface CRC Errors
0x07 ===== = = === == Solid State Device Statistics (rev 1) ==
0x07 0x008 1 0 --- Percentage Used Endurance Indicator
|||_ C monitored condition met
||__ D supports DSN
|___ N normalized value
Pending Defects log (GP Log 0x0c) supported [please try: '-l defects']
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 1 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 2 Device-to-host register FISes sent due to a COMRESET
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC
0x0002 2 0 R_ERR response for data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
More information about the Smartmontools-database
mailing list