[Smartmontools-database] USB HDD (ADATA NH13 125f:a13a)
deim31
deim31 at gmail.com
Fri May 25 12:49:47 CEST 2018
Hi all,
wanna contribute with device (actually only USB bridge) not in list:
USB HDD ADATA NH13
125f:a13a
(works with -d sat)
gentoo linux 4.16.9-gentoo
smartmontools 6.6 (smartctl 6.6 2017-11-05 r4594)
# lsusb -v -d 125f:a13a
Bus 004 Device 007: ID 125f:a13a A-DATA Technology Co., Ltd.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 3.00
bDeviceClass 0
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 9
idVendor 0x125f A-DATA Technology Co., Ltd.
idProduct 0xa13a
bcdDevice 1.00
iManufacturer 2 ADATA
iProduct 3 NH13
iSerial 1 xxxxxxxxx
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 44
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk-Only
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 15
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 15
Binary Object Store Descriptor:
bLength 5
bDescriptorType 15
wTotalLength 22
bNumDeviceCaps 2
USB 2.0 Extension Device Capability:
bLength 7
bDescriptorType 16
bDevCapabilityType 2
bmAttributes 0x00000002
HIRD Link Power Management (LPM) Supported
SuperSpeed USB Device Capability:
bLength 10
bDescriptorType 16
bDevCapabilityType 3
bmAttributes 0x00
wSpeedsSupported 0x000e
Device can operate at Full Speed (12Mbps)
Device can operate at High Speed (480Mbps)
Device can operate at SuperSpeed (5Gbps)
bFunctionalitySupport 1
Lowest fully-functional device speed is Full Speed (12Mbps)
bU1DevExitLat 10 micro seconds
bU2DevExitLat 2047 micro seconds
can't get debug descriptor: Resource temporarily unavailable
Device Status: 0x000d
Self Powered
U1 Enabled
U2 Enabled
# smartctl -d sat --all /dev/sdf
smartctl 6.6 2017-11-05 r4594 [x86_64-linux-4.16.9-gentoo] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Toshiba 2.5" HDD MQ01ABD...
Device Model: TOSHIBA MQ01ABD100
Serial Number: xxxxx
LU WWN Device Id: 5 000039 612883f64
Firmware Version: AX1P1A
User Capacity: 1 000 204 886 016 bytes [1,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Fri May 25 12:02:08 2018 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 242) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always
- 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail
Offline - 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always
- 1890
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always
- 28209
5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always
- 296
7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always
- 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail
Offline - 0
9 Power_On_Hours 0x0032 084 084 000 Old_age Always
- 6615
10 Spin_Retry_Count 0x0033 253 100 030 Pre-fail Always
- 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always
- 77
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always
- 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always
- 22
193 Load_Cycle_Count 0x0032 094 094 000 Old_age Always
- 67201
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always
- 38 (Min/Max 16/47)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always
- 34
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always
- 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always
- 0
220 Disk_Shift 0x0002 100 100 000 Old_age Always
- 0
222 Loaded_Hours 0x0032 098 098 000 Old_age Always
- 934
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always
- 0
224 Load_Friction 0x0022 100 100 000 Old_age Always
- 0
226 Load-in_Time 0x0026 100 100 000 Old_age Always
- 260
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail
Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Thanks,
d.
More information about the Smartmontools-database
mailing list